Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 204 | Manualshive

Страница: 204 / 444

background image

Configuration Commands

Page 204

7750 SR OS Interface Configuration Guide

configured parameters. The exception parameters for the protection channel can be configured in
the

config>port>aps>sonet-sdh

context.

Signal failure (SF) and signal degrade (SD) alarms are not enabled by default on POS interfaces.
It is recommended to change the default alarm notification configuration for POS ports that
belong to APS groups in order to be notified of SF/SD occurrences to be able to interpret the
cause for an APS group to switch the active line.

For path alarms, modify the logical line aps-id in the

configure>port aps-

id

<sonet-sdh>path

report-alarm

context. For example:

configure port

aps-1

sonet-sdh path report-alarm p-ais

For line alarms, separately, modify the 2 physical ports that are members of the logical aps-id
port (the working and protect lines). APS reacts only to line alarms, not path alarms.
For example:

configure port

1/2/3

sonet-sdh report-alarm lb2er-sd

configure port

4/5/6

sonet-sdh report-alarm lb2er-sd

For example:

A:ALA-48>config>port>aps# info

----------------------------------------------

working-circuit 1/2/3

protect-circuit 4/5/6

----------------------------------------------

A:ALA-48>config>port>aps#

If the SD and SF threshold rates must be modified, the changes must be performed at the line
level on both the working and protect APS port member.

The

no

form of this command deletes an aps-

group-id

or bundle-aps-group-id. In order for an

aps-

group-id

to be deleted,

The same rules apply for physical ports, bundles deletions apply to APS ports/bundles deletions
(for example an aps-group-id must be shutdown, have no service configuration on it, and no path
configuration on it). In addition working and protection circuits must be removed before an aps-
group-id may be removed.

Syntax:

port

aps

-

group-id

aps

:

keyword

group-id

:

1 — 64

Example

:

port

aps

-64

bpgrp-id —

Creates a bundle protection group (BPG). The BPGrp consists of a working and

protection bundles that provide APS protection to each other using bi-directional APS as
supported on the 7750 SR-Series family of products. All members of a working/protection
bundle must be on the same working/protection circuit respectively of the same, already
provisioned APS group.
The working bundle must have already been created in the

config>port

context before services

can be created on a BPGrp.

«
...
202
203
204
205
206
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: STONEFLY Страницы: 48

Бренд: TP-Link Страницы: 2

Бренд: ZyXEL Communications Страницы: 299

StorageWorks AIT 35GB AutoLoader

Бренд: Compaq Страницы: 4

SUPERLOADER DLT MAGAZINE

Бренд: Tandberg Data Страницы: 6

Бренд: ICP DAS USA Страницы: 62

Бренд: INNOSILICON Страницы: 11

TeraStation WSS WS5020N6

Бренд: Buffalo Страницы: 115

Бренд: TRENDnet Страницы: 205

Бренд: Gbord Страницы: 11

Бренд: ZyXEL Communications Страницы: 4

Бренд: Zhone Страницы: 494

Бренд: Vivotek Страницы: 185

Бренд: MSE Страницы: 35

Бренд: Cisco Страницы: 22

Бренд: Tripp Lite Страницы: 2

Бренд: IntraServer Technology Страницы: 16

Бренд: D-Link Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды