Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 256 | Manualshive

Страница: 256 / 444

background image

Configuration Commands

Page 256

7750 SR OS Interface Configuration Guide

section-trace

Syntax

section-trace

{

increment-z0

|

byte

value

|

string

string

}

Context

config>port>sonet-sdh

Description

This command configures the section trace bytes in the SONET section header to interoperate with
some older versions of ADMs or regenerators that require an incrementing STM ID. You can
explicitly configure an incrementing STM value rather than a static one in the SDH overhead by
specifying the z0-increment.

Default

byte

0x1

Parameters

increment-z0 —

Configure an incrementing STM ID instead of a static value.

byte

value —

Set values in SONET header bytes.

Default

0x1

Values

0 — 255 or 0x00 — 0xFF

string

string —

Specifies a text string that identifies the section.

Values

A string up to 16 bytes.

single-fiber

Syntax

[

no

]

single-fiber

Context

config>port>sonet-sdh

Description

This command enables packet gathering and redirection of IP packets from a single fiber (RX) port of
the Ethernet or SONET/SDH interface and redistributes packets to other interfaces through either
static routes or policy-based forwarding.

This parameter can be applied in conjunction with the strip-label command. If they are applied
together, the port must have the single-fiber option configured before it can be associated with an
interface that is configured with the strip-label option.

Once a port is configured with single-fiber, traffic will no longer be transmitted out of that port. This
command can be used in conjunction with strip-label.

Default

no single-fiber

speed

Syntax

speed

{

oc3

|

oc12

}

no speed

Context

config>port>sonet-sdh

«
...
254
255
256
257
258
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 40

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 4

ShareCenter DNS-343

Бренд: D-Link Страницы: 12

AirPlus G DWL-G710

Бренд: D-Link Страницы: 5

MYDLINK DNR-322L

Бренд: D-Link Страницы: 4

mydlink DNR-312L

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 88

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 2

Бренд: i-MO Страницы: 58

RUGGEDSWITCH RS900G

Бренд: RuggedCom Страницы: 23

Бренд: Abocom Страницы: 2

InvenSense RoboKit1

Бренд: TDK Страницы: 13

Бренд: Patton Страницы: 62

Бренд: 2N Telekomunikace Страницы: 67

Fast EtherLink XL PCI 10/100BASE-TXNetwork Interface...

Бренд: 3Com Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды