Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 301 | Manualshive

Страница: 301 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 301

hash-key —

The hash key. The key can be any combination of ASCII characters up to 33 (hash1-key)

or 55 (hash2-key) characters in length (encrypted). If spaces are used in the string, enclose the
entire string in quotation marks (“ ”).

hash —

Specifies the key is entered in an encrypted form. If the hash or hash2 parameter is not used,

the key is assumed to be in a non-encrypted, clear text form. For security, all keys are stored in
encrypted form in the configuration file with the hash or hash2 parameter specified.

hash2 —

Specifies the key is entered in a more complex encrypted form that involves more variables

then the key value alone, this means that hash2 encrypted variable cannot be copied and pasted.
If the hash or hash2 parameter is not used, the key is assumed to be in a non-encrypted, clear text
form. For security, all keys are stored in encrypted form in the configuration file with the hash or
hash2 parameter specified.

mc-lag

Syntax

[

no

]

mc-lag

Context

config>redundancy>multi-chassis>peer>mc-lag

Description

This command enables the context to configure multi-chassis LAG operations and related parameters.

The

no

form of this command administratively disables multi-chassis LAG. MC-LAG can only be

issued only when mc-lag is shutdown.

hold-on-neighbor-failure

Syntax

hold-on-neighbor-failure

multiplier

no hold-on-neighbor-failure

Context

config>redundancy>multi-chassis>peer>mc-lag

Description

This command specifies the interval that the standby node will wait for packets from the active node
before assuming a redundant-neighbor node failure. This delay in switch-over operation is required to
accommodate different factors influencing node failure detection rate, such as IGP convergence, or
HA switch-over times and to prevent the standby node to take action prematurely.

The

no

form of this command sets this parameter to default value.

Default

3

Parameters

multiplier —

The time interval that the standby node will wait for packets from the active node before

assuming a redundant-neighbor node failure.

Values

2 — 25

«
...
299
300
301
302
303
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: 4IPNET Страницы: 97

Бренд: Queclink Страницы: 9

Бренд: NA Страницы: 22

Бренд: NetComm Страницы: 69

Бренд: Sierra Wireless Страницы: 2

Бренд: iNetVu Страницы: 20

AirStation G54 WLA2-G54

Бренд: Buffalo Страницы: 8

Бренд: Planet Страницы: 13

Бренд: AMG Страницы: 4

Бренд: Paradyne Страницы: 46

Бренд: ADF Web Страницы: 20

BiPAC 8200AXL-1200

Бренд: Billion Страницы: 94

Бренд: NASdeluxe Страницы: 6

Бренд: Tripp Lite Страницы: 2

Бренд: Tripp Lite Страницы: 2

Бренд: D-Link Страницы: 95

Бренд: D-Link Страницы: 124

Бренд: D-Link Страницы: 164

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды