Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 289

Страница: 289 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 289

report-alarm

Syntax

[

]

report-alarm

[

ais

] [

los

] [

oof

] [

rai

] [

looped

] [

ber-sd

] [

ber-sf

]

Context

config>port>tdm>ds1
config>port>tdm>e1

Description

This command enables logging of DS-1/DS-3 or E-1/E-3 alarms for DS-1/DS-3 or E-1/E-3 ports or
channels.

The

form of this command disables logging of the specified alarms.

Parameters

ais —

Reports alarm indication signal errors. When configured,

ais

alarms are not raised and cleared.

Default

ais

alarms are issued

los —

Reports loss of signal errors. When configured,

los

traps are not raised and cleared.

Default

los

traps are issued.

oof —

Reports out-of-frame errors. When configured,

oof

alarms are not raised and cleared.

Default

oof

alarms are not issued.

rai —

Reports resource availability indicator events. When configured,

rai

events are not raised and

cleared.

Default

rai

alarms are not issued

looped —

Reports looped packets errors.

Default

looped

alarms are not issued

lof —

Reports loss of frame errors. When configured,

lof

traps are not raised and cleared.

Default

lof

traps are issued

signal-mode

Syntax

signal-mode

{

cas

}

Context

config>port>tdm>ds1
config>port>tdm>e1

Description

This command activates the signal mode on the channel. When enabled, it uses routing information to
direct the payload of voice or data to its destination.

Parameters

cas —

Specifies channel associated signaling.

speed

Syntax

speed

{

}

Context

config>port>tdm>ds1>channel-group

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды