manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 15 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 15

7750 SR OS Interface Configuration Guide

Page 15

G

ETTING

 S

TARTED

In This Chapter

This chapter provides process flow information to configure cards, MDAs and ports.

Alcatel-Lucent 7750 SR-Series Router Configuration Pro-
cess

Table 1

 lists the tasks necessary to provision input/output control modules (IOMs), also referred to 

as cards, Media Dependent Adapters (MDAs), and ports.

This guide is presented in an overall logical configuration flow. Each section describes a software 
area and provides CLI syntax and command usage to configure parameters for a functional area.

Table 1: Configuration Process

Area

Task

Chapter 

Provisioning

Chassis slots and cards

Chassis Slots and Cards on page 18

MDAs

MDAs on page 18

Versatile Service Module

Versatile Service Module (VSM) on page 20

Ports

Ports on page 30

Reference

List of IEEE, IETF, and other 
proprietary entities.

Standards and Protocol Support on page 439

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов