Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 444

background image

Digital Diagnostics Monitoring

Page 30

7750 SR OS Interface Configuration Guide

Ports

Port Types

Before a port can be configured, the slot must be provisioned with a card type and MDA type
specified.

The Alcatel-Lucent 7750 SR routers support the following port types:

•

Ethernet — Supported Ethernet port types include Fast Ethernet (10/100BASE-T),
Gigabit (1000BASE-T) and 10Gigabit Ethernet (10GBASE-X) ports on an appropriate
MDA. SR-Series ports must be configured as either access or network. The default is
network.

→

Access ports — Configured for customer facing traffic on which services are
configured. If a Service Access Port (SAP) is to be configured on the port or channel,
it must be configured as an access port or channel. When a port is configured for
access mode, the appropriate encapsulation type must be configured to distinguish the
services on the port or channel. Once a port has been configured for access mode, one
or more services can be configured on the port or channel depending on the
encapsulation value.

→

Network ports — Configured for network facing traffic. Network ports participate in
the service provider transport or infrastructure network. Dot1q is supported on
network ports.

•

SONET-SDH and TDM — Supported SONET-SDH and TDM port types include:

→

n*DS-0 inside DS-1/E-1

→

DS-1/E-1DS-3/E-3

→

OC3/STM-1

→

OC12/STM-4

→

OC48/STM-16

→

OC192/STM-64 SONET/SDH

A SONET/SDH port/path or a TDM port/channel can be configured with the following
encapsulations depending on the MDA type:

→

ATM

Some MDAs support ATM encapsulation on SONET/SDH and TDM ports. The ATM cell
format and can be configured for either UNI or NNI cell format. The format is
configurable on a SONET/SDH or TDM port/channel path basis. All VCs on a path,
channel or port must use the same cell format. The ATM cell mapping can also be
configured on per-interface basis for either Direct or PLCP on some MDAs (for example
ASAP MDA).

«
...
28
29
30
31
32
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

IntelliJack NJ200

Бренд: 3Com Страницы: 4

Бренд: ICP DAS USA Страницы: 8

Бренд: Idis Страницы: 31

Бренд: Patton electronics Страницы: 65

FieldPoint cFP-RTD-122

Бренд: National Instruments Страницы: 15

Бренд: IDT Страницы: 207

Бренд: Xantech Страницы: 16

Бренд: Softing Страницы: 16

Бренд: ZyXEL Communications Страницы: 2

Бренд: Allynk Technology Страницы: 39

Бренд: ZyXEL Communications Страницы: 114

ROUTE FINDER RFIPSC-1

Бренд: Multitech Страницы: 54

Бренд: ProCurve Страницы: 2

Бренд: Paradyne Страницы: 6

Бренд: TCL Страницы: 38

Бренд: TCL Страницы: 23

Бренд: Moxa Technologies Страницы: 94

BiPAC 8200AXL-1200

Бренд: Billion Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды