Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 24

Configuration Overview

Page 24

7750 SR OS Interface Configuration Guide

Channelized Any Service Any Port (ASAP) CHOC-3/STM-1

Each port for the channelized ASAP OC-3/STM-1 MDA supports channelization down to DS-0
and accepts one OC-3/STM-1 SFP small form factor pluggable (SFP) module. The same SFP
optics used on Alcatel-Lucent’s SONET/SDH MDAs can be used on the channelized ASAP OC-
3/STM-1 MDA.

Each channelized OC-3/STM-1 supports up to 512 channels with DS-0 timeslots with per channel
encapsulation configuration (for example, Frame Relay, PPP, cHDLC, ATM). DS-3 TDM
channels can be further channelized to DS-1/E-1 channel groups. An E3 TDM channel cannot be
channelized and can only be configured in clear channel operation. The MDA is based on a
programmable data path architecture that enables enhanced L1 and L2 data path functionality, for
example ATM TM features, MDA-based channel/port queuing, or multilink applications like
Inverse ATM Multiplexing (IMA).

Channelized OC-12/STM-4 ASAP MDAs

The 1-port and 4-port channelized OC-12/STM-4 variant of the ASAP MDAs have features and
channelization options similar to the existing 4-port channelized OC-3/STM-1 ASAP MDA.

DS-3 TDM channels can be further channelized to DS-1/E-1 channel groups. An E-3 TDM
channel cannot be channelized and can only be configured in clear channel operation.

Channelized DS-3/E-3 ASAP MDA (4-Port)

The 4-port MDA provides 4 ports configurable as DS-3 or E-3. The MDA has eight (8) 1.0/2.3
connectors and accepts up to eight (8) DS-3/E-3 coax patch cables.

Each physical DS-3 connection can support a full clear-channel DS-3, or it can be channelized into
independent DS-1/E-1 data channels. Each DS-1/E-1 channel can then be further channelized
down to DS-0s. E-3 ports do not support channelization, only clear channel operation.

Channelized DS-3/E-3 ASAP MDA (12-Port)

The 12-port MDA provides 12 ports configurable as DS-3 or E-3. The MDA has twenty-four (24)
1.0/2.3 connectors and accepts up to twenty-four (24) DS-3/E-3 coax patch cables.

«
...
22
23
24
25
26
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов