Toshiba Q9 Plus ASD, Installation & Operation Manual

Page: 68 / 434

S15 ASD
MODEL RANGE 1/4 HP to 3 HP 1/2 HP to 20 HP 1/2 HP to 20 HP
Voltage Rating Single-Phase 230 VAC Three-Phase 230 VAC Three-Phase 460 VAC
POWER REQUIREMENTS
Input Tolerance Voltage: ±10%; Frequency: ±5%
Output Frequency 0.1 to 500 Hz
CONTROL SPECIFICATIONS
Control Method Sinusodial Pulse Width Modulation (PWM); Flux-Field Current Vector Control; Set Point Control (PID)
Voltage Regulation Main Circuit Voltage Feedback Control: Automatic, Fixed, & Off
V/Hz Control V/f Constant, Variable Torque, Automatic Torque Boost, Vector Control, PM Motor Control, 5-point V/F Custom Setting, & Auto-Tuning
PWM Carrier Frequency Adjustable 2 to 16 kHz (For Drive Specific Information Consult Factory)
Frequency Setting Rotary Encoder Integrated into EOI, 0 to 10 VDC, ±10VDC, 4 to 20 mA, Digital Input, Binary Input, & Motorized Potentiometer Input
Frequency Precision Analog Input ±0.5% of Maximum Output Frequency; Discrete/Communications Input ±0.01% of Maximum Output Frequency
Speed Regulation Open Loop: Up to 0.1%, 60:1 Speed Range
Main Protective Functions
Stall Prevention, Current Limit, Over-Current, Output Short Circuit, Over-Voltage, Over-Voltage Limit, Undervoltage, Ground Fault
Detection, Input Phase Failure, Output Phase Failure, Overload Protection by Electronic Thermal Function, Armature Over-Current
at Start-Up, Load Side Over-Current at Start-Up, Over-Torque, Undercurrent, Overheating, Cumulative Operation Time, Life Alarm,
Emergency Stop, & Various Pre-alarms
Retry User-Set Number of Retries for Automatic System Restart After Trip
Restart Able to Smoothly Catch Freewheeling Motor (Bidirectional)
Overload Current Rating 110% Continuous; 150% for 1 Minute
CONTROL INTERFACE
Digital Input 6 Discrete Input Terminals Programmable to 110 Functions (May Be Increased Using Optional Hardware)
Digital Output 3 Discrete Output Terminals Programmable to 150 Functions; 1 Form-A Contact, 1 Form-C Contact, & 1 Open Collector Output
Analog Input 3 Programmable: One 4 to 20 mA Input, One 0 to 10 VDC Input, & One ±10 VDC Input
Analog Output 1 Programmable: 4 to 20 mA or 0 to 10 VDC
Communication Ports RS485 Port (TSB or MODBUS RTU Protocol)
ELECTRONIC OPERATOR INTERFACE (EOI)
Display 4x20 Graphical Full-English LCD Back-Lit Display for Programming, Monitoring, & Diagnostics
LED Indicators Run (Red)/Stop (Green), Hand (Green), & DC Bus Charge Indicator (Red)
Keys Run, Prg, Mon, Status, %, Hz, Stop, Mode, & Easy Key; Rotary Encoder for Parameter Navigation, Settings, & Control
Monitoring
Frequency Command Screen; Multiple Parameters Displayed: Output Frequency, Forward/Reverse Run, Output Current, Input Volt-
age (DC Detection), Output Voltage, Torque, Inverter Load Factor, Motor Load Factor, Braking Resistor Load Factor, Input Power,
Output Power, Input Terminal status, Output Terminal Status, Overload/Regional Setting, PID Feedback Value, Stator Frequency,
Parts Replacement Alarm, Cumulative Operation Time, & Past Trips
CONSTRUCTION
Enclosure RAL 7016 (Anthracite Gray); IP20; Wall-Mount; Front-Access Only
Power Cables Bottom Access for Input/Motor Cables
Cooling Self-Cooling/ Forced Air-Cooled
Standards & Compliances UL Listed in US & Canada, CSA, & CE
AMBIENT CONDITIONS
Ambient Temperature 0 to 60°C (Note: See Manual for Details, Ambient Temperatures Above 50°C May Require a De-Rate)
Altitude 3300 ft. Above Sea Level (Up to 10,000 ft. with Derate)
Humidity 95% Maximum (Non-Condensing)
Installation
Indoors; No Direct Sunlight; Protects from Corrosive Gas/Explosive Gas/Flammable Gas/Oil Mist/Dust; Vibration of Less Than
5.9 m/s
2
(10 to 55 Hz)
© 2012 Toshiba International Corporation • Industrial Division • 13131 West Little York Road • Houston, Texas 77041 USA • Tel +713-466-0277 US 1-800-231-1412 • Rev. 120411
www.toshiba.com/ind
TOSHIBA INDUSTRIAL PRODUCTS:
• Adjustable Speed Drives
• Motors
• Motor Controls
• Instrumentation & PLCs
• Uninterruptible Power Systems