Texas Instruments AM1808 Technical Reference Manual Download Page 5

Page: 5 / 1820

www.ti.com

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Contents

9.6

ARM Sleep Mode Management

........................................................................................

193

9.6.1

ARM Wait-For-Interrupt Sleep Mode

..........................................................................

193

9.6.2

ARM Clock OFF

..................................................................................................

194

9.6.3

ARM Subsystem Clock ON

.....................................................................................

194

9.7

RTC-Only Mode

...........................................................................................................

195

9.8

Dynamic Voltage and Frequency Scaling (DVFS)

...................................................................

195

9.8.1

Frequency Scaling Considerations

............................................................................

195

9.8.2

Voltage Scaling Considerations

................................................................................

196

9.9

Deep Sleep Mode

.........................................................................................................

196

9.9.1

Entering/Exiting Deep Sleep Mode Using Externally Controlled Wake-Up

..............................

197

9.9.2

Entering/Exiting Deep Sleep Mode Using RTC Controlled Wake-Up

.....................................

198

9.9.3

Deep Sleep Sequence

..........................................................................................

199

9.9.4

Entering/Exiting Deep Sleep Mode Using Software Handshaking

........................................

200

9.10

Additional Peripheral Power Management Considerations

..........................................................

200

9.10.1

USB PHY Power Down Control

..............................................................................

200

9.10.2

DDR2/mDDR Memory Controller Clock Gating and Self-Refresh Mode

................................

201

9.10.3

SATA PHY Power Down

.......................................................................................

201

9.10.4

LVCMOS I/O Buffer Receiver Disable

.......................................................................

201

9.10.5

Pull-Up/Pull-Down Disable

.....................................................................................

202

System Configuration (SYSCFG) Module

.............................................................................

203

10.1

Introduction

................................................................................................................

204

10.2

Protection

..................................................................................................................

204

10.2.1

Privilege Mode Protection

.....................................................................................

204

10.2.2

Kicker Mechanism Protection

.................................................................................

205

10.3

Master Priority Control

...................................................................................................

205

10.4

Interrupt Support

..........................................................................................................

207

10.4.1

Interrupt Events and Requests

................................................................................

207

10.4.2

Interrupt Multiplexing

...........................................................................................

207

10.5

SYSCFG Registers

.......................................................................................................

207

10.5.1

Revision Identification Register (REVID)

....................................................................

209

10.5.2

Device Identification Register 0 (DEVIDR0)

.................................................................

209

10.5.3

Boot Configuration Register (BOOTCFG)

...................................................................

210

10.5.4

Chip Revision Identification Register (CHIPREVIDR)

.....................................................

210

10.5.5

Kick Registers (KICK0R-KICK1R)

............................................................................

211

10.5.6

Host 0 Configuration Register (HOST0CFG)

...............................................................

212

10.5.7

Interrupt Registers

..............................................................................................

213

10.5.8

Fault Registers

..................................................................................................

216

10.5.9

Master Priority Registers (MSTPRI0-MSTPRI2)

............................................................

218

10.5.10

Pin Multiplexing Control Registers (PINMUX0-PINMUX19)

.............................................

221

10.5.11

Suspend Source Register (SUSPSRC)

....................................................................

262

10.5.12

Chip Signal Register (CHIPSIG)

............................................................................

265

10.5.13

Chip Signal Clear Register (CHIPSIG_CLR)

..............................................................

266

10.5.14

Chip Configuration 0 Register (CFGCHIP0)

...............................................................

267

10.5.15

Chip Configuration 1 Register (CFGCHIP1)

...............................................................

268

10.5.16

Chip Configuration 2 Register (CFGCHIP2)

...............................................................

271

10.5.17

Chip Configuration 3 Register (CFGCHIP3)

...............................................................

273

10.5.18

Chip Configuration 4 Register (CFGCHIP4)

...............................................................

274

10.5.19

VTP I/O Control Register (VTPIO_CTL)

...................................................................

275

10.5.20

DDR Slew Register (DDR_SLEW)

..........................................................................

277

10.5.21

Deep Sleep Register (DEEPSLEEP)

.......................................................................

278

10.5.22

Pullup/Pulldown Enable Register (PUPD_ENA)

..........................................................

279

10.5.23

Pullup/Pulldown Select Register (PUPD_SEL)

............................................................

279

10.5.24

RXACTIVE Control Register (RXACTIVE)

.................................................................

281

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for AM1808

Reviews:

Brands by name

Popular brands

Texas Instruments AM1808, Technical Reference Manual

Search results

Summary of Contents for AM1808

Reviews:

Brands by name

Popular brands