manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 706

Registers

www.ti.com

706

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

Enhanced Direct Memory Access (EDMA3) Controller

17.4.3.6.18 Destination FIFO Memory Protection Proxy Register n (DFMPPRXYn)

The destination FIFO memory protection proxy register

n

(DFMPPRXY

n

) is shown in

Figure 17-108

and

described in

Table 17-91

.

Figure 17-108. Destination FIFO Memory Protection Proxy Register n (DFMPPRXYn)

31

16

Reserved

R-0

15

9

8

7

4

3

0

Reserved

PRIV

Reserved

PRIVID

R-0

R-0

R-0

R-0

LEGEND: R = Read only; -

n

= value after reset

Table 17-91. Destination FIFO Memory Protection Proxy Register n (DFMPPRXYn)

Field Descriptions

Bit

Field

Value

Description

31-9

Reserved

0

Reserved

8

PRIV

Privilege level. This contains the privilege level used by the EDMA programmer to set up the parameter
entry in the channel controller. This field is set up when the associated TR is submitted to the
EDMA3TC.

The privilege ID is used while issuing Read and write command to the target endpoints so that the
target endpoints can perform memory protection checks based on the PRIV of the host that set up the
DMA transaction.

0

User-level privilege

1

Supervisor-level privilege

7-4

Reserved

0

Reserved

3-0

PRIVID

0-Fh

Privilege ID. This contains the Privilege ID of the EDMA programmer that set up the parameter entry in
the channel controller. This field is set up when the associated TR is submitted to the EDMA3TC.

This PRIVID value is used while issuing Read and write commands to the target endpoints so that the
target endpoints can perform memory protection checks based on the PRIVID of the host that set up
the DMA transaction.

0

For any other master that sets up the PaRAM entry

1

If CPU sets up the PaRAM entry

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands