manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 1384

Registers

www.ti.com

1384

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

Serial ATA (SATA) Controller

28.4.10 BIST FIS Count Register (BISTFCTR)

The BIST FIS count register (BISTFCTR) contains the received BIST FIS count in the loopback initiator
far-end retimed, far-end analog and near-end analog modes. It is updated each time a new BIST FIS is
received. It is reset by Global reset, Port reset (COMRESET) or by setting the BISTCR.CNTCLR bit. This
register does not roll over and freezes when the FFFF FFFFh value is reached. It takes approximately 65
hours of continuous BIST operation to reach this value. The BISTFCTR is shown in

Figure 28-10

and

described in

Table 28-14

.

Figure 28-10. BIST FIS Count Register (BISTFCTR)

31

0

BISTFCTR

R/W-0

LEGEND: R/W = Read/Write; -

n

= value after reset

Table 28-14. BIST FIS Count Register (BISTFCTR) Field Description

Bit

Field

Value

Description

31-0

BISTFCTR

0-FFFF FFFFh

Received BIST FIS Count.

28.4.11 BIST Status Register (BISTSR)

The BIST status register (BISTSR) contains errors detected in the received BIST FIS in the loopback
initiator far-end retimed, far-end analog and near-end analog modes. It is updated each time a new BIST
FIS is received. It is reset by Global reset, Port reset (COMRESET) or by setting the BISTCR.CNTCLR bit.
The BISTSR is shown in

Figure 28-11

and described in

Table 28-15

.

Figure 28-11. BIST Status Register (BISTSR)

31

24

23

16

Reserved

BRSTERR

R-0

R-0

15

0

FRAMERR

W-0

LEGEND: R = Read only; W = Write only; -

n

= value after reset

Table 28-15. BIST Status Register (BISTSR) Field Description

Bit

Field

Value

Description

31-24

Reserved

0

Reserved.

23-16

BRSTERR

0-FFh

Burst Error. This bit field contains the burst error count. It is accumulated each time a burst error
condition is detected: DWORD error is detected in the received frame and 1.5 seconds (27,000
frames) passed since the previous burst error was detected. The BRSTERR value does not roll
over and freezes at FFh. This bit field is updated if BIST_MODE = DWORD.

15-0

FRAMERR

0-FFFFh

Frame Error. This bit field contains the frame error count. It is accumulated (new value is added to
the old value) each time a new BIST frame with a CRC error is received. The FRAMERR value
does not roll over and freezes at FFFFh.

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands