manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 579

DMA/QDMA

channel

logic

PaRAM

Transfer

request

submission

Completion

and error

interrupt

logic

EDMA3_1_
CC0_INT[3:0]

EDMA3_1_
CC0_ERRINT

Completion

detection

To/from

EDMA3

programmer

EDMA3_1_CC0

TC0

Transfer

controllers

Read/write
commands
and data

EDMA3_1_
TC0_ERRINT

MMR

Event

queue

DMA/QDMA

channel

logic

PaRAM

Transfer

request

submission

Completion

and error

interrupt

logic

EDMA3_0_
CC0_INT[3:0]

EDMA3_0_
CC0_ERRINT

Completion

detection

To/from

EDMA3

programmer

EDMA3_0_CC0

TC0

Transfer

controllers

Read/write
commands
and data

EDMA3_0_

TC0_ERRINT

MMR

TC1

commands

Read/write

and data

MMR

EDMA3_0_
TC1_ERRINT

Event

queue(s)

www.ti.com

Introduction

579

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

Enhanced Direct Memory Access (EDMA3) Controller

17.1.3 Functional Block Diagram

Figure 17-1

shows a block diagram of the EDMA3 controller.

Figure 17-1. EDMA3 Controller Block Diagram

17.1.4 Terminology Used in This Document

The following are some terms used in this chapter.

Term

Meaning

A-synchronized
transfer

A transfer type where 1 dimension is serviced per synchronization event.

AB-synchronized
transfer

A transfer type where 2 dimensions are serviced per synchronization event.

Chaining

A trigger mechanism in which a transfer can be initiated at the completion of
another transfer or subtransfer.

CPU(s)

The main processing engine or engines on a device.

DMA channel

A channel that can be triggered by external, manual, and chained events. All DMA
channels exist in the EDMA3CC.

Dummy set or
Dummy PaRAM set

A PaRAM set for which at least one of the count fields is equal to 0 and at least
one of the count fields is nonzero. A null PaRAM set has all the count set fields
cleared.

Dummy transfer

A dummy set results in the EDMA3CC performing a dummy transfer. This is not an
error condition. A null set results in an error condition.

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands