Texas Instruments AM1808 Technical Reference Manual Download Page 1694

Page: 1694 / 1820

Registers

www.ti.com

1694

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Universal Serial Bus 2.0 (USB) Controller

34.4.1 Revision Identification Register (REVID)

The revision identification register (REVID) contains the revision for the USB 2.0 OTG controller module.
The REVID is shown in

Figure 34-27

and described in

Table 34-31

Figure 34-27. Revision Identification Register (REVID)

REV

R-4EA1 0800h

LEGEND: R = Read only; -

= value after reset

Table 34-31. Revision Identification Register (REVID) Field Descriptions

Bit

Field

Value

Description

31-0

REV

4EA1 0800h

Revision ID of the USB module.

34.4.2 Control Register (CTRLR)

The control register (CTRLR) allows the CPU to control various aspects of the module. The CTRLR is
shown in

Figure 34-28

and described in

Table 34-32

Figure 34-28. Control Register (CTRLR)

Reserved

R-0

Reserved

RNDIS

UINT

Reserved

CLKFACK

RESET

R-0

R/W-0

R-0

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -

= value after reset

Table 34-32. Control Register (CTRLR) Field Descriptions

Bit

Field

Value

Description

31-5

Reserved

RNDIS

Global RNDIS mode enable for all endpoints.

Global RNDIS mode is disabled.

Global RNDIS mode is enabled.

UINT

USB non-PDR interrupt handler enable.

PDR interrupt handler is enabled.

PDR interrupt handler is disabled.

Reserved

CLKFACK

Clock stop fast ACK enable.

Clock stop fast ACK is disabled.

Clock stop fast ACK is enabled.

RESET

Soft reset.

No effect.

Writing a 1 starts a module reset. The USB controller will clear this bit when it completes reset.

«
...
1692
1693
1694
1695
1696
...
»

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for AM1808

Reviews:

Related manuals for AM1808

Brands by name

Popular brands

Texas Instruments AM1808, Technical Reference Manual

Search results

Summary of Contents for AM1808

Reviews:

Related manuals for AM1808

Brands by name

Popular brands