manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 997

www.ti.com

Architecture

997

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

Inter-Integrated Circuit (I2C) Module

22.2.8 NACK Bit Generation

When the I2C peripheral is a receiver (master or slave), it can acknowledge or ignore bits sent by the
transmitter. To ignore any new bits, the I2C peripheral must send a no-acknowledge (NACK) bit during the
acknowledge cycle on the bus.

Table 22-2

summarizes the various ways the I2C peripheral sends a

NACK bit.

Table 22-2. Ways to Generate a NACK Bit

NACK Bit Generation

I2C Peripheral
Condition

Basic

Optional

Slave-receiver mode

• Disable data transfers (STT = 0 in ICSTR).

• Allow an overrun condition (RSFULL = 1 in

ICSTR).

• Reset the peripheral (IRS = 0 in ICMDR)

.

Set the NACKMOD bit of ICMDR before the rising
edge of the last data bit you intend to receive.

Master-receiver mode
AND
Repeat mode
(RM = 1 in ICMDR)

• Generate a STOP condition (STOP = 1 in

ICMDR).

• Reset the peripheral (IRS = 0 in ICMDR).

Set the NACKMOD bit of ICMDR before the rising
edge of the last data bit you intend to receive.

Master-receiver mode
AND
Nonrepeat mode
(RM = 0 in ICMDR)

• If STP = 1 in ICMDR, allow the internal data

counter to count down to 0 and force a STOP
condition.

• If STP = 0, make STP = 1 to generate a

STOP condition.

• Reset the peripheral (IRS = 0 in ICMDR).

Set the NACKMOD bit of ICMDR before the rising
edge of the last data bit you intend to receive.

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands