Texas Instruments AM1808 Technical Reference Manual Download Page 1581 | Manualshive

Page: 1581 / 1820

background image

Introduction

1581

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

Universal Serial Bus OHCI Host Controller

33.1 Introduction

33.1.1 Purpose of the Peripheral

The USB1.1 OHCI host controller (HC) is a single port controller that communicates with USB devices at
the USB low-speed (1.5M bit-per-second maximum) and full-speed (12M bit-per-second maximum) data
rates. It is compatible with the

Universal Serial Bus Specification Revision 2.0

and the

Open HCI—Open

Host Controller Interface Specification for USB, Release 1.0a

, available through the Compaq Computer

Corporation web site, and hereafter called the

OHCI Specification for USB

. It is assumed that users of the

USB1.1 host controller are already familiar with the

USB Specification

and

OHCI Specification for USB

.

The USB1.1 host controller implements the register set and makes use of the memory data structures
defined in the

OHCI Specification for USB

. These registers and data structures are the mechanisms by

which a USB host controller driver software package can control the USB1.1 host controller. The

OHCI

Specification for USB

also defines how the USB host controller implementation must interact with those

registers and data structures in system memory.

To reduce processor software and interrupt overhead, the USB1.1 host controller generates USB traffic
based on data structures and data buffers stored in system memory. The USB1.1 host controller accesses
these data structures without direct intervention by the processor using its bus master port. These data
structures and data buffers can be located in internal or external system RAM.

The USB1.1 host controller provides an interrupt to the ARM.

«
...
1579
1580
1581
1582
1583
...
»

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AM1808

Brand: Jetter Pages: 35

Brand: Qualys Pages: 2

Brand: Furuno Pages: 24

Brocade X6-8 Director

Brand: Broadcom Pages: 207

640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU

Brand: Intel Pages: 105

Brand: Intellinet Pages: 2

Brand: JETWAY Pages: 63

BPN-SAS3-116A-N10

Brand: Supermicro Pages: 8

Brand: ADLINK Technology Pages: 34

Brand: netsys Pages: 38

Brand: Boser Pages: 54

Brand: Altera Pages: 43

Brand: I-Tech Pages: 6

Supereta Series DC/DC

Brand: TDK Pages: 2

Alto Room Scaffold

Brand: Lakeside Pages: 12

Brand: JETWAY Pages: 41

TALKSWITCH 24-CA

Brand: Talkswitch Pages: 9

Brand: Xcellon Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands