manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 1702

Registers

www.ti.com

1702

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

Universal Serial Bus 2.0 (USB) Controller

34.4.11 USB Interrupt Source Clear Register (INTCLRR)

The USB interrupt source clear register (INTCLRR) allows the CPU to acknowledge an interrupt source
and turn it off. A read of this register returns the USB interrupt source register value. The INTCLRR is
shown in

Figure 34-37

and described in

Table 34-41

.

NOTE:

Other than the USB bit field, to make use of INTCLRR, the PDR interrupt handler must be

enabled (the UINT bit in the control register (CTRLR) is cleared to 0). If the UINT bit in
CTRLR is set to 1, you need to use the interrupt status/flag from the core register space.

Figure 34-37. USB Interrupt Source Clear Register (INTCLRR)

31

25

24

16

Reserved

USB

R-0

R/W-0

15

13

12

9

8

5

4

1

0

Reserved

RXEP[

n

]

Reserved

TXEP[

n

]

EP0

R-0

R/W-0

R-0

R/W-0

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -

n

= value after reset

Table 34-41. USB Interrupt Source Clear Register (INTCLRR) Field Descriptions

Bit

Field

Value

Description

31-25

Reserved

0

Reserved

24-16

USB

0-1FFh

Write a 1 to clear equivalent USB interrupt source. Allows the CPU to acknowledge a USB interrupt
source and turn it off.

15-13

Reserved

0

Reserved

12-9

RXEP[

n

]

Clear receive endpoint

n

interrupt source. Allows the CPU to acknowledge a receive endpoint

n

interrupt source and turn it off.

0

RXEP

n

interrupt is not cleared.

1

RXEP

n

interrupt is cleared.

8-5

Reserved

0

Reserved

4-1

TXEP[

n

]

Clear transmit endpoint

n

interrupt source. Allows the CPU to acknowledge a transmit endpoint

n

interrupt source and turn it off.

0

TXEP

n

interrupt is not cleared.

1

TXEP

n

interrupt is cleared.

0

EP0

Clear endpoint 0 interrupt source. Allows the CPU to acknowledge the endpoint 0 interrupt source and
turn it off.

0

Endpoint 0 interrupt is not cleared.

1

Endpoint 0 interrupt is cleared.

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands