manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 268

SYSCFG Registers

www.ti.com

268

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

System Configuration (SYSCFG) Module

10.5.15 Chip Configuration 1 Register (CFGCHIP1)

The chip configuration 1 register (CFGCHIP1) controls the following functions:

•

eCAP0/1/2 event input source: Allows using McASP0 TX/RX events as eCAP event input sources.

•

HPI Control: Allows HPIEN bit control that determines whether or not the HPI module has control over
the HPI pins (multiplexed with other peripheral pins). It also provides configurability to select whether
the host address is a word address or a byte address mode.

•

EDMA3_1 Transfer Controller Default Burst Size (DBS) Control: This controls the maximum number of
bytes issued per read/write command or the burst size for the individual transfer controllers (TCs) on
the device. By default for all transfer controllers, the burst size is set to 16 bytes. However, CFGCHIP1
allows configurability of this parameter so that the TC can have a burst size of 16, 32, or 64 bytes. The
burst size determines the intra packet efficiency for the EDMA3_1 transfers. Additionally, it also
facilitates preemption at a system level, as all transfer requests are internally broken down by the
transfer controller up to DBS size byte chunks and on a system level, each master’s priority
(configured by the MSTPRI register) is evaluated at burst size boundaries. The DBS value can
significantly impact the standalone throughput performance depending on the source and destination
(bus width/frequency/burst support etc) and the TC FIFO size, etc. Therefore, the DBS size
configuration should be carefully analyzed to meet the system’s throughput/performance requirements.

•

eHRPWM Time Base Clock (TBCLK) Synchronization: Allows the software to globally synchronize all
enabled eHRPWM modules to the time base clock (TBCLK).

•

McASP0 AMUTEIN signal source control: Allows selecting GPIO interrupt from different banks as
source for the McASP0 AMUTEIN signal.

The CFGCHIP1 is shown in

Figure 10-42

and described in

Table 10-46

.

Figure 10-42. Chip Configuration 1 Register (CFGCHIP1)

31

27

26

22

21

17

16

CAP2SRC

CAP1SRC

CAP0SRC

HPIBYTEAD

R/W-0

R/W-0

R/W-0

R/W-0

15

14

13

12

11

8

HPIENA

EDMA31TC0DBS

TBCLKSYNC

Reserved

R/W-0

R/W-0

R/W-0

R/W-0

7

4

3

0

Reserved

AMUTESEL0

R/W-0

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -

n

= value after reset

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands