STMicroelectronics STM32F405 Reference Manual Download | Manualshive

Page: 132 / 1731

background image

Power controller (PWR)

RM0090

DocID018909 Rev 11

Note:

If the application needs to disable the external clock before entering Stop mode, the HSEON
bit must first be disabled and the system clock switched to HSI.
Otherwise, if the HSEON bit is kept enabled while the external clock (external oscillator) can
be removed before entering stop mode, the clock security system (CSS) feature must be
enabled to detect any external oscillator failure and avoid a malfunction behavior when
entering stop mode.

Exiting Stop mode (for STM32F405xx/07xx and STM32F415xx/17xx)

The Stop mode is exited according to

Section : Exiting low-power mode

for more details on how to exit Stop mode.

When exiting Stop mode by issuing an interrupt or a wakeup event, the HSI RC oscillator is
selected as system clock.

When the voltage regulator operates in low-power mode, an additional startup delay is
incurred when waking up from Stop mode. By keeping the internal regulator ON during Stop
mode, the consumption is higher although the startup time is reduced.

Table 27. Stop mode entry and exit (for STM32F405xx/07xx and STM32F415xx/17xx)

Stop mode

Description

Mode entry

WFI (Wait for Interrupt) or WFE (Wait for Event) while:
– No interrupt (for WFI) or event (for WFE) is pending,
– SLEEPDEEP bit is set in Cortex

®

-M4 with FPU System Control register,

– PDDS bit is cleared in Power Control register (PWR_CR),
– Select the voltage regulator mode by configuring LPDS bit in PWR_CR.

On Return from ISR:
– No interrupt is pending,
– SLEEPDEEP bit is set in Cortex

®

-M4 with FPU System Control register,

– SLEEPONEXIT = 1,
– PDDS bit is cleared in Power Control register (PWR_CR).

Note: To enter Stop mode, all EXTI Line pending bits (in

Pending register

), all peripheral interrupts pending bits, the RTC Alarm

(Alarm A and Alarm B), RTC wakeup, RTC tamper, and RTC time
stamp flags, must be reset. Otherwise, the Stop mode entry
procedure is ignored and program execution continues.

«
...
130
131
132
133
134
...
»

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

Brand: Sole Diesel Pages: 8

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

Brand: Yardney Pages: 8

Brand: HABONIM Pages: 9

Brand: FAAC Pages: 32

Brand: Hama Pages: 7

Brand: Hama Pages: 44

Brand: RadioMaster Pages: 10

Brand: K&K Pages: 6

Brand: tams elektronik Pages: 12

Brand: janitza Pages: 58

Brand: Sanhua Pages: 3

Brand: Watts Pages: 24

Extra Free RZB-02

Brand: Zamel Pages: 2

Brand: Yamaha Pages: 2

Brand: ZKTeco Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands