STMicroelectronics STM32F405 Reference Manual Download | Manualshive

Page: 272 / 1731

background image

General-purpose I/Os (GPIO)

RM0090

DocID018909 Rev 11

8.3.2 I/O

pin

multiplexer and mapping

The microcontroller I/O pins are connected to onboard peripherals/modules through a
multiplexer that allows only one peripheral’s alternate function (AF) connected to an I/O pin
at a time. In this way, there can be no conflict between peripherals sharing the same I/O pin.

Each I/O pin has a multiplexer with sixteen alternate function inputs (AF0 to AF15) that can
be configured through the GPIOx_AFRL (for pin 0 to 7) and GPIOx_AFRH (for pin 8 to 15)
registers:

•

After reset all I/Os are connected to the system’s alternate function 0 (AF0)

•

The peripherals’ alternate functions are mapped from AF1 to AF13

•

Cortex

®

-M4 with FPU EVENTOUT is mapped on AF15

This structure is shown in

below.

In addition to this flexible I/O multiplexing architecture, each peripheral has alternate
functions mapped onto different I/O pins to optimize the number of peripherals available in
smaller packages.

To use an I/O in a given configuration, proceed as follows:

•

System function

Connect the I/O to AF0 and configure it depending on the function used:
–

JTAG/SWD, after each device reset these pins are assigned as dedicated pins
immediately usable by the debugger host (not controlled by the GPIO controller)

–

RTC_REFIN: this pin should be configured in Input floating mode

–

MCO1 and MCO2: these pins have to be configured in alternate function mode.

Note:

You can disable some or all of the JTAG/SWD pins and so release the associated pins for
GPIO usage.

For more details please refer to

Section 7.2.10: Clock-out capability

and

Section 6.2.10:

Clock-out capability

«
...
270
271
272
273
274
...
»

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

Brand: zipwake Pages: 12

Brand: Watts Pages: 2

Brand: jbc Pages: 12

Brand: Calsense Pages: 74

Elemec3 013-02-0095-002

Brand: GAI-Tronics Pages: 12

Brand: HandyTrac Pages: 14

Brand: TA Pages: 6

Brand: Laird Pages: 38

Brand: Laird Pages: 5

Brand: Keba Pages: 16

Brand: KEB Pages: 16

sensoCOMFORT VRC 720/3

Brand: Vaillant Pages: 64

Brand: Fox Pages: 5

Brand: M-system Pages: 13

Brand: DeLaval Pages: 102

Brand: HBM Pages: 88

SatService sat-nms VLC

Brand: Calian Pages: 40

EZ Power Remote

Brand: Pogo Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands