STMicroelectronics STM32F405 Reference Manual Download

Page: 246 / 1731

Reset and clock control for STM32F405xx/07xx and STM32F415xx/17xx(RCC)

RM0090

246/1731

DocID018909 Rev 11

Bits 31:30 Reserved, must be kept at reset value.

Bit 29

DACEN:

DAC interface clock enable

Set and cleared by software.
0: DAC interface clock disabled
1: DAC interface clock enable

Bit 28

PWREN:

Power interface clock enable

Set and cleared by software.
0: Power interface clock disabled
1: Power interface clock enable

Bit 27 Reserved, must be kept at reset value.

Bit 26

CAN2EN:

CAN 2 clock enable

Set and cleared by software.
0: CAN 2 clock disabled
1: CAN 2 clock enabled

Bit 25

CAN1EN:

CAN 1 clock enable

Set and cleared by software.
0: CAN 1 clock disabled
1: CAN 1 clock enabled

Bit 24 Reserved, must be kept at reset value.

Bit 23

I2C3EN:

I2C3 clock enable

Set and cleared by software.
0: I2C3 clock disabled
1: I2C3 clock enabled

Bit 22

I2C2EN:

I2C2 clock enable

Set and cleared by software.
0: I2C2 clock disabled
1: I2C2 clock enabled

Bit 21

I2C1EN:

I2C1 clock enable

Set and cleared by software.
0: I2C1 clock disabled
1: I2C1 clock enabled

Bit 20

UART5EN:

UART5 clock enable

Set and cleared by software.
0: UART5 clock disabled
1: UART5 clock enabled

Bit 19

UART4EN:

UART4 clock enable

Set and cleared by software.
0: UART4 clock disabled
1: UART4 clock enabled

Bit 18

USART3EN:

USART3 clock enable

Set and cleared by software.
0: USART3 clock disabled
1: USART3 clock enabled

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for STM32F405

Reviews:

Related manuals for STM32F405

Brands by name

Popular brands

STMicroelectronics STM32F405, Reference Manual

Search results

Summary of Contents for STM32F405

Reviews:

Related manuals for STM32F405

Brands by name

Popular brands