STMicroelectronics STM32F405 Reference Manual Download

Page: 171 / 1731

DocID018909 Rev 11

171/1731

RM0090

Reset and clock control for STM32F42xxx and STM32F43xxx (RCC)

212

Bit 25

ETHMACRST:

Ethernet MAC reset

This bit is set and cleared by software.
0: does not reset Ethernet MAC
1: resets Ethernet MAC

Bit 24 Reserved, must be kept at reset value.

Bit 23

DMA2DRST

: DMA2D reset

This bit is set and reset by software.
0: does not reset DMA2D
1: resets DMA2D

Bit 22

DMA2RST:

DMA2 reset

This bit is set and cleared by software.
0: does not reset DMA2
1: resets DMA2

Bit 21

DMA1RST:

DMA2 reset

This bit is set and cleared by software.
0: does not reset DMA2
1: resets DMA2

Bits 20:13 Reserved, must be kept at reset value.

Bit 12

CRCRST:

CRC reset

This bit is set and cleared by software.
0: does not reset CRC
1: resets CRC

Bit 11 Reserved, must be kept at reset value.

Bit 10

GPIOKRST

: IO port K reset

This bit is set and cleared by software.
0: does not reset IO port K
1: resets IO port K

Bit 9

GPIOJRST

: IO port J reset

This bit is set and cleared by software.
0: does not reset IO port J
1: resets IO port J

Bit 8

GPIOIRST:

IO port I reset

This bit is set and cleared by software.
0: does not reset IO port I
1: resets IO port I

Bit 7

GPIOHRST:

IO port H reset

This bit is set and cleared by software.
0: does not reset IO port H
1: resets IO port H

Bit 6

GPIOGRST:

IO port G reset

This bit is set and cleared by software.
0: does not reset IO port G
1: resets IO port G

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for STM32F405

Reviews:

Related manuals for STM32F405

Brands by name

Popular brands

STMicroelectronics STM32F405, Reference Manual

Search results

Summary of Contents for STM32F405

Reviews:

Related manuals for STM32F405

Brands by name

Popular brands