STMicroelectronics STM32F405 Reference Manual Download | Manualshive

Page: 396 / 1731

background image

Analog-to-digital converter (ADC)

RM0090

DocID018909 Rev 11

Figure 46. Analog watchdog’s guarded area

13.3.8 Scan

mode

This mode is used to scan a group of analog channels.

The Scan mode is selected by setting the SCAN bit in the ADC_CR1 register. Once this bit
has been set, the ADC scans all the channels selected in the ADC_SQRx registers (for
regular channels) or in the ADC_JSQR register (for injected channels). A single conversion
is performed for each channel of the group. After each end of conversion, the next channel
in the group is converted automatically. If the CONT bit is set, regular channel conversion
does not stop at the last selected channel in the group but continues again from the first
selected channel.

If the DMA bit is set, the direct memory access (DMA) controller is used to transfer the data
converted from the regular group of channels (stored in the ADC_DR register) to SRAM
after each regular channel conversion.

The EOC bit is set in the ADC_SR register:

•

At the end of each regular group sequence if the EOCS bit is cleared to 0

•

At the end of each regular channel conversion if the EOCS bit is set to 1

The data converted from an injected channel are always stored into the ADC_JDRx
registers.

Table 66. Analog watchdog channel selection

Channels guarded by the analog

watchdog

ADC_CR1 register control bits (x = don’t care)

AWDSGL bit

AWDEN bit

JAWDEN bit

None

x

0

0

All injected channels

0

0

1

All regular channels

0

1

0

All regular and injected channels

0

1

1

Single

(1)

injected channel

1. Selected by the AWDCH[4:0] bits

1

0

1

Single

regular channel

1

1

0

Single

regular or injected channel

1

1

1

!NALOGVOLTAGE

(IGHERTHRESHOLD

,OWERTHRESHOLD

'UARDEDAREA

(42

,42

AI

«
...
394
395
396
397
398
...
»

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

Brand: Baader Planetarium Pages: 7

Brand: Beaphar Pages: 2

Brand: Samson Pages: 52

Brand: Samson Pages: 32

Brand: Danfoss Pages: 59

MorphoAccess SIGMA Extreme Series

Brand: Safran Pages: 79

Brand: Lawler Pages: 5

Brand: K'Nex Education Pages: 56

Brand: Sanhua Pages: 3

Brand: QED Pages: 26

Brand: Saftronics Pages: 13

Brand: UNICORECOMM Pages: 32

Brand: UNICORECOMM Pages: 7

Brand: UNICORECOMM Pages: 26

Brand: UNICORECOMM Pages: 25

Brand: WAREMA Pages: 4

Brand: Yoshitake Pages: 4

Brand: YOKOGAWA Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands