STMicroelectronics STM32F405 Reference Manual Download | Manualshive

Page: 809 / 1731

background image

DocID018909 Rev 11

RM0090

Real-time clock (RTC)

828

Bit 16

ADD1H

: Add 1 hour (summer time change)

When this bit is set outside initialization mode, 1 hour is added to the calendar time. This bit
is always read as 0.
0: No effect

1: Adds 1 hour to the current time. This can be used for summer time change

Bit 15

TSIE

: Timestamp interrupt enable

0: Timestamp Interrupt disable

1: Timestamp Interrupt enable

Bit 14

WUTIE

: Wakeup timer interrupt enable

0: Wakeup timer interrupt disabled

1: Wakeup timer interrupt enabled

Bit 13

ALRBIE

:

Alarm B interrupt enable

0: Alarm B Interrupt disable

1: Alarm B Interrupt enable

Bit 12

ALRAIE

: Alarm A interrupt enable

0: Alarm A interrupt disabled

1: Alarm A interrupt enabled

Bit 11

TSE

: Time stamp enable

0: Time stamp disable

1: Time stamp enable

Bit 10

WUTE

: Wakeup timer enable

0: Wakeup timer disabled

1: Wakeup timer enabled

Bit 9

ALRBE

:

Alarm B enable

0: Alarm B disabled

1: Alarm B enabled

Bit 8

ALRAE:

Alarm A enable

0: Alarm A disabled

1: Alarm A enabled

Bit 7

DCE:

Coarse digital calibration enable

0: Digital calibration disabled

1: Digital calibration enabled
PREDIV_A must be 6 or greater

Bit 6

FMT

: Hour format

0: 24 hour/day format

1: AM/PM hour format

Bit 5

BYPSHAD

: Bypass the shadow registers

0: Calendar values (when reading from RTC_SSR, RTC_TR, and RTC_DR) are taken from
the shadow registers, which are updated once every two RTCCLK cycles.
1: Calendar values (when reading from RTC_SSR, RTC_TR, and RTC_DR) are taken
directly from the calendar counters.

Note: If the frequency of the APB1 clock is less than seven times the frequency of RTCCLK,

BYPSHAD must be set to ‘1’.

«
...
807
808
809
810
811
...
»

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

Brand: ABB Pages: 52

Brand: Vacon Pages: 64

Brand: Canarm Pages: 3

Brand: Manfrotto Pages: 16

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

PowerXL DX-NET-ETHERCAT-2

Brand: Eaton Pages: 3

Brand: Harmonic Drive Pages: 25

Brand: Nelson Pages: 8

Centronic SunWindControl SWC245-II

Brand: Becker Pages: 52

Waukesha Cherry-Burrell D4 Series

Brand: SPX FLOW Pages: 34

Brand: Mosa Pages: 28

Brand: Geberit Pages: 12

multicomp F144-MS-1V1C1TI6RO-3

Brand: KBR Pages: 68

Brand: Valcom Pages: 9

Brand: olympia electronics Pages: 22

Alano FlipIt 1760447

Brand: Graco Pages: 136

Brand: SFC Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands