STMicroelectronics STM32F405 Reference Manual Download | Manualshive

Page: 104 / 1731

background image

Embedded Flash memory interface

RM0090

DocID018909 Rev 11

Bit 31

LOCK:

Lock

Write to 1 only. When it is set, this bit indicates that the FLASH_CR register is locked. It is
cleared by hardware after detecting the unlock sequence.
In the event of an unsuccessful unlock operation, this bit remains set until the next reset.

Bits 30:26 Reserved, must be kept cleared.

Bit 25

ERRIE:

Error interrupt enable

This bit enables the interrupt generation when the OPERR bit in the FLASH_SR register is set
to 1.

0: Error interrupt generation disabled
1: Error interrupt generation enabled

Bit 24

EOPIE:

End of operation interrupt enable

This bit enables the interrupt generation when the EOP bit in the FLASH_SR register goes to
1.

0: Interrupt generation disabled
1: Interrupt generation enabled

Bits 23:17 Reserved, must be kept cleared.

Bit 16

STRT:

Start

This bit triggers an erase operation when set. It is set only by software and cleared when the
BSY bit is cleared.

Bits 15:10 Reserved, must be kept cleared.

Bits 9:8

PSIZE[1:0]:

Program size

These bits select the program parallelism.

00 program x8
01 program x16
10 program x32
11 program x64

Bit 7 Reserved, must be kept cleared.

Bits 6:3

SNB[3:0]:

Sector number

These bits select the sector to erase.

0000 sector 0
0001 sector 1
...
1011 sector 11
Others not allowed

Bit 2

MER:

Mass Erase

Erase activated for all user sectors.

Bit 1

SER:

Sector Erase

Sector Erase activated.

Bit 0

PG:

Programming

Flash programming activated.

«
...
102
103
104
105
106
...
»

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

Brand: NCR Pages: 6

Brand: CALEFFI Pages: 12

QuickSetter+ 132 Series

Brand: CALEFFI Pages: 5

Brand: Eaton Pages: 6

Brand: Eaton Pages: 35

Brand: Eaton Pages: 18

Brand: Eaton Pages: 73

Brand: Eaton Pages: 4

Cutler-Hammer IQ DP-4000

Brand: Eaton Pages: 87

Brand: Eaton Pages: 14

Brand: Eaton Pages: 36

Brand: J3C Pages: 2

Brand: YOKOGAWA Pages: 2

ALICAT SCIENTIFIC PC

Brand: Halma Pages: 2

ALICAT SCIENTIFIC PCD

Brand: Halma Pages: 46

Brand: Lattice Pages: 23

Brand: Lattice Semiconductor Pages: 2

Brand: Lathem Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands