manualshive.com logo in svg

STMicroelectronics STM32F405, Reference Manual

The STMicroelectronics STM32F405 is a powerful microcontroller featuring a Cortex-M4 core, ideal for embedded applications. To get the most out of this product, make sure to download the free Reference Manual from manualshive.com. The manual provides detailed information on how to maximize the STM32F405's capabilities.

Share
Download
background image

General-purpose timers (TIM2 to TIM5)

RM0090

638/1731

DocID018909 Rev 11

18.4.20  TIM5 option register (TIM5_OR)

Address offset: 0x50

Reset value: 0x0000

          

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Reserved

TI4_RMP

Reserved

rw

rw

Bits 15:8 Reserved, must be kept at reset value.

Bits 7:6

TI4_RMP:

 Timer Input 4 remap

Set and cleared by software.
00: TIM5 Channel4 is connected to the GPIO: Refer to the Alternate function mapping table 
in the datasheets.

 

01: the LSI internal clock is connected to the TIM5_CH4 input for calibration purposes

 

10: the LSE internal clock is connected to the TIM5_CH4 input for calibration purposes

 

11: the RTC wakeup interrupt is connected to TIM5_CH4 input for calibration purposes. 
Wakeup interrupt should be enabled. 

Bits 5:0 Reserved, must be kept at reset value.

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

D-Link DSN-640 Quick Installation Manual preview
DSN-640
Brand: D-Link Pages: 40
Bartec MAK 3003 Manual preview
MAK 3003
Brand: Bartec Pages: 26
Baninni VIGO Manual preview
VIGO
Brand: Baninni Pages: 26
V2 CU1 Manual preview
CU1
Brand: V2 Pages: 48
TCS CS-105 Quick Start Manual preview
CS-105
Brand: TCS Pages: 16
Velleman VM130V2SET Quick Start Manual preview
VM130V2SET
Brand: Velleman Pages: 26
Velleman VM151 Manual preview
VM151
Brand: Velleman Pages: 32
Velocity MMP Operation And Maintenance Manual preview
MMP
Brand: Velocity Pages: 84
We Care Solar Suitcase Installation Manual preview
Suitcase
Brand: We Care Solar Pages: 46
Watts 757 Series Assembly Manual preview
757 Series
Brand: Watts Pages: 4
Watts OneFlow OFTWH-R Installation And Operation Manual preview
OneFlow OFTWH-R
Brand: Watts Pages: 8
Zamel Extra Free RZB-02 Quick Manual preview
Extra Free RZB-02
Brand: Zamel Pages: 2
Yamaha DCP4S-US Owner'S Manual preview
DCP4S-US
Brand: Yamaha Pages: 2
Klimaire KUMR-903 Operation Manual preview
KUMR-903
Brand: Klimaire Pages: 5
Multi-Clean 421914 Quick Start Manual preview
421914
Brand: Multi-Clean Pages: 4
Primo Water PRWF-80455 Instructions Manual preview
PRWF-80455
Brand: Primo Water Pages: 10
PENGWYN 485-1P-JS Technical Manual preview
485-1P-JS
Brand: PENGWYN Pages: 32
Warner Electric CBC-801-1 Installation Instructions And Service Manual preview
CBC-801-1
Brand: Warner Electric Pages: 6

Brands by name

Popular brands

Load more brands