STMicroelectronics SPEAr300 Reference Manual Download Page 707 | Manualshive

Page: 707 / 844

background image

RM0082

RS_SDIO controller

Doc ID 018672 Rev 1

32.7.10 HOSTCTRL

register

The HOSTCTRL bit assignments are given in

Table 629.

HOSTCTRL register bit assignments

Bit

Name

Reset
value

Type

Description

[07]

CDSD

1’h0

RW

This bit selects source for card detection.

1’b1- The card detect test level is selected

1’b0 -SDCD# is selected (for normal use)

[06]

CDTL

1’h0

RW

This bit is enabled while the Card Detect Signal
Selection is set to 1 and it indicates card inserted or
not.

1’b1 - Card Inserted

1’b0 - No Card

[05]

SD8MODE

1’h0

RW

This bit selects the data width of the HC. The HD
shall select it to match the data width of the SD card.

1’b1 - 8 bit mode is selected

1’b0 - 8 bit mode is not selected

[04:03]

DMASEL

2’h0

RW

One of supported DMA modes can be selected. The
host driver shall check support of DMA modes by
referring the Capabilities register.

2’b00 - SDMA is selected

2’b01 - 32 bit Address ADMA1 is selected

2’b10 -32 bit Address ADMA2 is selected

2’b11 - 64 bit Address ADMA2 is selected

[02]

HSEN

1’h0

RW

This bit is optional. Before setting this bit, the HD
shall check the High Speed Support in the
capabilities register. If this bit is set to logic ‘0’
(default), the HC outputs CMD line and DAT lines at
the falling edge of the SD clock (up to 25 MHz). If this
bit is set to logic ‘1’, the HC outputs CMD line and
DAT lines at the rising edge of the SD clock (up to 50
MHz)

1’b1 - High Speed Mode

1’b0 - Normal Speed Mode

[01]

DTW

1’h0

RW

This bit selects the data width of the HC. The HD
shall select it to match the data width of the SD card.

1’b1 - 4 bit mode

1’b0 - 1 bit mode

[00]

LEDCTRL

1’b0

RW

This bit is used to caution the user not to remove the
card while the SD card is being accessed. It is not
necessary to change for each transaction.

1’b1 - LED on

1’b0 - LED off

«
...
705
706
707
708
709
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: Samson Pages: 124

Brand: Samson Pages: 86

Brand: VAC Pages: 5

Brand: National Instruments Pages: 34

Brand: D+H Pages: 32

Brand: Anilam Pages: 31

Brand: Allen-Bradley Pages: 88

ZigBee Pro VT8000 Series

Brand: Viconics Pages: 3

Brand: Trikdis Pages: 7

Brand: Velleman-Kit Pages: 32

Brand: KEPCO Pages: 34

Integrated Controller Rev C EZ-ZONE PM

Brand: Watlow Pages: 80

Brand: digitalview Pages: 18

Brand: Nitrous Express Pages: 20

Brand: Intel Pages: 334

Brand: JR Pages: 88

BaseStation 1000

Brand: Base Line Pages: 11

Brand: Trio Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands