STMicroelectronics SPEAr300 Reference Manual Download Page 310 | Manualshive

Page: 310 / 844

background image

BS_Serial memory interface

RM0082

Doc ID 018672 Rev 1

Table 243.

SMI_SR register bit assignments

Bit

Name

Reset
value

Type

Description

[31:16]

Reserved

-

-

Read: undefined.

[15:14]

WM

2’h0

RO

Write mode for selected bank.

This 2 bit field report the write mode (

Section 15.5.2

for the four supported memory banks. Each bit is associated
to a single bank (specifically the LSB, bit [12], refers to
Bank0). A bit is set in case related bank is in write mode,
that is, when a write enable command – opcode 8’h06 – is
sent to the relevant memory bank. Note: The WM field is not
cleared by instructions sent in software mode.

[13:12]

-

-

-

Not Used.

[11]

ERF1

1’h0

RO

Error flag 1: forbidden access.

This bit is used to issue error flags concerning access to
external memory. Specifically, if set ERF1 marks forbidden
access to memory, that is: read/write access requested on
disabled bank, read/write access requested in software
mode, or read requests in write burst mode (bit WBM set in
SMI_CR1 register,

Section 15.8.3

[10]

ERF2

1’h0

RO

Error flag 2: forbidden Write request.

T

his bit is used to issue error flags concerning access to

external memory. Specifically, if set ERF2 marks specific
forbidden write request, that is: write requests when out of
write mode (bit WM cleared in this register for relevant
bank), size changed between two consecutive write
requests, or address is not incremented. Note: Setting
either ERF1 or ERF2, an ERROR response is sent back to
AHB master on HRESP.

[09]

WCF

1’h0

RO

Write complete flag.

This bit is set in case of write completion, that is when the
WIP bit of SMSR is set to 1‘b0 (stating the end of
programming). After a write instruction, a read status
register command (opcode 8’h05) is performed by
hardware.

«
...
308
309
310
311
312
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

PACSystems* RX3i

Brand: GE Pages: 39

PACSystems* RX3i

Brand: GE Pages: 35

PACSystems* RX3i

Brand: GE Pages: 3

PACSystems* RX3i

Brand: GE Pages: 169

Brand: Samson Pages: 48

Brand: QED Pages: 26

Brand: Eaton Pages: 448

Cutler-Hammer LMR

Brand: Eaton Pages: 38

Brand: SYCLOPE Pages: 60

Brand: HQ Power Pages: 23

Brand: PENGWYN Pages: 32

Brand: Warner Electric Pages: 6

Brand: Gateway Pages: 2

Brand: Oriental motor Pages: 4

Brand: Barco Pages: 4

SatService sat-nms VLC

Brand: Calian Pages: 40

AUTOMATIONWORX IBS PCI SC/I-T

Brand: Phoenix Contact Pages: 80

BMS NUV100-CI-12

Brand: Nuvation Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands