STMicroelectronics SPEAr300 Reference Manual Download Page 57 | Manualshive

Page: 57 / 844

background image

RM0082

Product overview

Doc ID 018672 Rev 1

4.1.1 Main

features

The following main functionalities are implemented in SPEAr300 embedded MPU device:

●

ARM926EJ-S core @333 MHz, 16+16 KB-I/D cache, configurable TCM-I/D size, MMU,
TLB, JTAG and ETM trace module (multiplexed interfaces).

●

Dynamic power saving features.

●

High performance linked list 8-channel DMA.

●

Multi-port memory controller: 8/16 bit mobileDDR@166 MHz or DDR2@333 MHz.

●

USB2.0 Host (High-Full-Low speed); integrated PHY transceiver.

●

USB2.0 Device (High-Full speed); integrated PHY transceiver.

●

Ethernet 10/100 MAC with MII Interface (IEEE-802.3)

●

I2C (High-Fast-Low speed) Master/Slave.

●

Cryptographic co-processor (C3).

●

IrDA controller with a data rate from 9.6 Kbps to 4 Mbps.

●

Touchscreen support (using ADC).

●

RTC - WDT - SYSCTR - MISC internal control registers.

●

ADC (1us/1MSPS) 8 analog input channels; 10 bit resolution.

●

JPEG codec accelerator single clock per pixel encoding decoding.

●

6 x 16 bits general purpose Timers with programmable prescaler (only 4 timers with
capture mode).

●

32KB ROM & up to 56 KB internal SRAM

●

Flexible static memory controller (FSMC) up to 16 bit data bus width, supporting
external asynchronous SRAM, NAND/NOR Flash.

●

3 x SPI Master/Slave (Motorola-Texas_National) Master/Slave up to 50 Mbps.

●

SDIO interface supporting SPI, SD1, SD4 and SD8 mode with card detect, write
protect, LED.

●

I2S interface, full duplex with data buffer for left and right channels allowing up to 64 ms
of voice buffer (for 32 bit samples).

The I2S and SDIO interfaces share the same RAM

resources.

●

UART with HW flow control (speed rate up to 3 Mbps)

●

Up to 512 timeslots, master or slave TDM. Any input timeslot can be switched to any
output timeslot, and/or can be buffered for computation (up to 16 channels of 1 to 4
timeslots buffered during 32 ms). Up to 16 buffers can be played in output timeslots.

●

Up to 8 additional I2C/SPI chip selects.

●

Camera interface ITU-601 with external or embedded synchronization (ITU-656 or
CSI2). Picture limit is given by the line length that must be stored in a 2048*32 buffer.

●

Color LCD Controller, supports up to 1024X768 resolution, 24 bpp true colour,
STN/TFT display panels.

●

9 x 9 keyboard controller.

●

18 GPIOs for CODEC (up to 8 quad CODECS) & SLIC management.

●

1 bit DAC

●

Up to 62 GPIOs (multiplexed with peripheral I/Os), up to 22 with interrupt capability.

●

Possible NAND / NOR Flash booting.

●

8/16 bits parallel Flash interface allowing connection of NOR or NAND Flash.

«
...
55
56
57
58
59
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: Parker Pages: 30

Brand: QED Pages: 26

Brand: Eaton Pages: 8

Brand: ABB Pages: 44

Brand: Omega Pages: 2

Brand: Zmotion Pages: 34

Brand: Daruifuno Pages: 24

Brand: Bender Pages: 28

Brand: Danfoss Pages: 36

SWD Starter Kit

Brand: ez-wheel Pages: 30

Brand: Aerotech Pages: 36

Brand: Fairchild Pages: 4

HYGRASREG KH-10

Brand: S+S Regeltechnik Pages: 16

Hauser COMPAX-M Series

Brand: Parker Pages: 84

Brand: Danfoss Pages: 44

Brand: Madas Pages: 48

CapSense Plus CY3280-CPM1

Brand: Cypress Pages: 4

Brand: Eaton Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands