STMicroelectronics SPEAr300 Reference Manual Download Page 721 | Manualshive

Page: 721 / 844

background image

RM0082

RS_SDIO controller

Doc ID 018672 Rev 1

Note:

Note: The host controller may sample the card Interrupt signal during interrupt period and
may hold its value in the flip-flop. If the Card Interrupt Status Enable is set to logic ‘0’, the HC
shall clear all internal signals regarding Card Interrupt.

32.7.20 ERRIRQSTATEN

register

The ERRIRQSTATEN bit assignments are given in

Table 641.

NIRQSTATEN register bit assignments

Bit

Name

Reset
value

Type

Description

[15]

FIX0

1’h0

RO

The HC shall control error Interrupts using the Error
Interrupt Status Enable register.

[14:09]

-

-

Rsvd

Reserved

[08]

CDIRQSTSEN

1’h0

RW

If this bit is set to logic ‘0’, the HC shall clear
Interrupt request to the System. The Card Interrupt
detection is stopped when this bit is cleared and
restarted when this bit is set to logic ‘1’. The HD
should clear the Card Interrupt Status Enable
before servicing the Card Interrupt and should set
this bit again after all Interrupt requests from the
card are cleared to prevent inadvertent Interrupts.

1’b0 - Masked

1’b1 - Enabled

[07]

CDRSTSEN

1’h0

RW

1’b0 - Masked

1’b1 - Enabled

[06]

CDISTSEN

1’h0

RW

[05]

BUFRDRDYEN 1’h0

RW

[04]

BUFWRRDYE
N

1’h0

RW

[03]

DMAIRQSTSE
N

1’h0

RW

[02]

BLKGESTSEN

1’h0

RW

[01]

TRNFCSTSEN

1’h0

RW

[00]

CMDCSTSEN

1’h0

RW

Table 642.

ERRIRQSTATEN register bit assignments

Bit

Name

Reset value

Type

Description

[15:14]

VDSERSTSEN

1’h0

RW1C

1’b0 - Masked

1’b1 - Enabled

[13]

CEATAERSTSEN

1’h0

RW1C

[12]

TGTRESERSTSEN

1’h0

RW1C

[11:10]

-

-

Rsvd

Reserved

«
...
719
720
721
722
723
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: Federal Signal Corporation Pages: 79

Brand: Federal Signal Corporation Pages: 32

MorphoAccess SIGMA Extreme Series

Brand: Idemia Pages: 31

Brand: HQ Power Pages: 23

eTracer ET4415BND

Brand: Epsolar Pages: 44

Brand: Engineering Solutions Pages: 34

NovoCon S Digital

Brand: Danfoss Pages: 2

Brand: Zeversolar Pages: 8

Brand: ECUE Pages: 39

Brand: Regada Pages: 41

Brand: Kelly Pages: 35

Brand: Nations Pages: 654

Brand: KELCO Pages: 4

Brand: Jordan Valve Pages: 5

Brand: RADIKAL TECHNOLOGIES Pages: 36

WALLACE & TIERNAN MULTI-FUNCTIONS-CONTROLLER

Brand: Evoqua Pages: 4

Brand: G-Scale Graphics Pages: 7

Brand: Oase Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands