STMicroelectronics SPEAr300 Reference Manual Download Page 442 | Manualshive

Page: 442 / 844

background image

HS_USB2.0 host

RM0082

Doc ID 018672 Rev 1

[09]

RWC

0b

R/W

R

RemoteWakeupConnected

This bit indicates whether HC supports remote wakeup
signaling. If remote wakeup is supported and used by the
system it is the responsibility of system firmware to set
this bit during POST. HC clears the bit upon a hardware
reset but does not alter it upon a software reset. Remote
wakeup signaling of the host system is host-bus-specific
and is not described in this specification.

[08]

IR

0b

R/W

R

InterruptRouting

This bit determines the routing of interrupts generated by
events registered in HcInterruptStatus. If clear, all
interrupts are routed to the normal host bus interrupt
mechanism. If set, interrupts are routed to the System
Management Interrupt. HCD clears this bit upon a
hardware reset, but it does not alter this bit upon a
software reset. HCD uses this bit as a tag to indicate the
ownership of HC.

[07:06]

HCFS

00b

R/W

R

HostControllerFunctionalState for USB

00b: USBRESET

01b: USBRESUME

10b: USBOPERATIONAL

11b: USBSUSPEND

A transition to USBOPERATIONAL from another state
causes SOF generation to begin 1 ms later. HCD may
determine whether HC has begun sending SOFs by
reading the StartofFrame field of

HcInterruptStatus.

This field may be changed by HC only when in the
USBSUSPEND state. HC may move from the
USBSUSPEND state to the USBRESUME state after
detecting the resume signaling from a downstream port.

HC enters USBSUSPEND after a software reset, whereas
it enters USBRESET after a hardware reset. The latter
also resets the RootHub and asserts subsequent reset
signaling to downstream ports.

[05]

BLE

0b

R/W

R

BulkListEnable

This bit is set to enable the processing of the Bulk list in
the next Frame. If cleared by HCD, processing of the Bulk
list does not occur after the next SOF. HC checks this bit
whenever it determines to process the list. When disabled,
HCD may modify the list. If HcBulkCurrentED is pointing
to an ED to be removed, HCD must advance the pointer
by updating HcBulkCurrentED before re-enabling
processing of the list.

Table 367.

HcControl register bit assignments (continued)

Bits

Name

Reset

Read/Write

Description

HCD

HC

«
...
440
441
442
443
444
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: J4C Pages: 4

Brand: Parker Pages: 30

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Max Charge MC-624

Brand: Balmar Pages: 8

MAX CHARGE MC-614

Brand: Balmar Pages: 20

Brand: Data Aire Pages: 13

Brand: ZKTeco Pages: 2

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: Gardner Denver Pages: 22

Brand: Hach Pages: 2

Brand: Hach Pages: 12

Brand: Hach Pages: 472

Brand: Hach Pages: 64

Brand: Hach Pages: 210

Brand: Vega Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands