STMicroelectronics SPEAr300 Reference Manual Download Page 252 | Manualshive

Page: 252 / 844

background image

Miscellaneous registers (Misc)

RM0082

Doc ID 018672 Rev 1

12.4.34 BIST1_STS_RES

register

The BIST1_STS_RES is an RO register which returns the functional BIST execution results
for the internal core memory group. The register bit assignments is given in the next table.

Table 186.

BIST4_CFG_CTR register bit assignments

BIST4_CFG_CTR Register

0x100

Bit

Name

Reset Value

Description

[31]

bist4_res_rst

1’h0

Reset status register result (BIST4_STS_RES):

1’b0: Disable reset

1’b1: Active reset

[30:29]

RFU

-

Reserved for future use (Write don’t care - Read return
zeros).

[28]

bist4_rst

1’h0

Reset BIST engine collar.

1’b0: Disable reset.

1’b1: Active reset.

[27]

[26]

[25]

[24]

bist4_tm

bist4_debug

bist4_ret

bist4_iddq

1’h0

1’h0

1’h0

1’h0

Memory BIST interface command:command code and
BIST engine actions are detailed in the Memory BIST
Command Table

[23:08]

RFU

-

[07:00]

rbact4

8’h0

Run BIST execution command (ref. Memory BIST
command):

1’b0: Disable BIST command.

1’b1: Run BIST command execution.

RBACT

Memory Cut

[00]

A926CM_rbact_dcache

[01]

A926CM_rbact_dcache

[02]

A926CM_rbact_dtag

[03]

A926CM_rbact_dvalid

[04]

A926CM_rbact_icache

[05]

A926CM_rbact_itag

[06]

A926CM_rbact_ivalid

[07]

A926CM_rbact_mmu

«
...
250
251
252
253
254
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: Jabra Pages: 8

Brand: WINDY NATION Pages: 16

Brand: Olsen Pages: 4

Brand: HANYOUNG NUX Pages: 4

Brand: J+J Pages: 56

EZ-ZONE PM L AAAAB Series

Brand: Watlow Pages: 30

Brand: KELCO Pages: 4

Brand: Hoffer Pages: 57

Brand: HIKVISION Pages: 5

Brand: Nexen Pages: 28

Brand: C Prox Ltd Pages: 9

ProcessLogix 1757-PLX52

Brand: Allen-Bradley Pages: 24

Brand: TRIAC Pages: 7

Brand: PXM Pages: 10

Brand: MAC3 Pages: 20

Brand: OptoSupply Pages: 4

Brand: Smartgen Pages: 46

ControlKeeper 2 CK2-120-NC

Brand: Greengate Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands