STMicroelectronics SPEAr300 Reference Manual Download Page 637 | Manualshive

Page: 637 / 844

background image

RM0082

LS_I2C controller

Doc ID 018672 Rev 1

28.6.23

IC_TXFLR and IC_RXFLR registers (0x074 - 0x078)

The IC_TXFLR (transmit FIFO level) and the IC_RXFLR (receive FIFO level) are RO
registers which contain the number of valid entries in the transmit and in the receive FIFO
buffer, respectively. The IC_TXFLR and IC_RXFLR bit assignments are given in

These registers increment whenever data is placed into the transmit or receive FIFO, and
decrement when data is taken from the transmit or receive FIFO. They are cleared when
either the I

2

C controller is disabled or whenever there is a transmission abort. Besides, the

IC_TXFLR register is cleared also if the slave bulk transfer mode (

Section 28.4.1: Slave

mode on page 612

) is aborted.

28.6.24 IC_TX_ABRT_SOURCE register (0x080)

The IC_TX_ABRT_SOURCE (Transmit Abort Source) is a RW register which indicates the
source of the transmission abort signal. This register is cleared whenever the processor
reads it or when the processor issues a clear signal to all interrupts. The
IC_TX_ABRT_SOURCE bit assignments are given in

.

[03]

RFNE

1’h0

Receive FIFO not empty.

If set, this bit indicates that the receive FIFO
contains one or more entries. This bit is cleared
when the receive FIFO is empty. This bit can be
polled by software to completely empty the receive
FIFO.

[02]

TFE

1’h1

Transmit FIFO completely empty.

If set, this bit indicates that the transmit FIFO is
completely empty. This bit is cleared when the
FIFO contains one or more valid entries. This bit
does not request an interrupt.

[01]

TFNF

1’h1

Transmit FIFO not full.

If set, this bit indicates that the transmit FIFO
contains one or more empty location (that is, it is
not full). This bit is cleared when it is full.

[00]

ACTIVITY

1’h0

I

2

C activity status.

Table 567.

IC_STATUS register bit assignments (continued)

Bit

Name

Reset
value

Description

Table 568.

IC_TXFLR and IC_RXFLR register bit assignments

Bit

Name

Type

Reset
value

Description

[31:04]

Reserved

-

Read: undefined. Write: should be zero.

[03:00]

TXFLR/ RXFLR

RO

4’h0

Transmit (or receive) FIFO level.

«
...
635
636
637
638
639
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: Walchem Pages: 10

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 20

Brand: YOKOGAWA Pages: 2

ALICAT SCIENTIFIC PC

Brand: Halma Pages: 2

ALICAT SCIENTIFIC PCD

Brand: Halma Pages: 46

Brand: RAM Pages: 71

Brand: IDTECK Pages: 12

Brand: Banner Pages: 2

CGLine+ Web Controller

Brand: Eaton Pages: 28

Omnicharge Solar OCS 100-20

Brand: tbs electronics Pages: 64

Brand: SOMFY Pages: 112

Brand: Festo Pages: 109

Brand: Topworx Pages: 8

Ambience Control 1

Brand: EuroLite Pages: 20

Brand: SKF Pages: 88

Brand: Engineering Solutions Pages: 34

NovoCon S Digital

Brand: Danfoss Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands