STMicroelectronics SPEAr300 Reference Manual Download Page 250 | Manualshive

Page: 250 / 844

background image

Miscellaneous registers (Misc)

RM0082

Doc ID 018672 Rev 1

12.4.32 BIST3_CFG_CTR

register

The BIST3_CFG_CTR is an R/W register which configures and controls the RAS-2 sub-
group memory BIST execution at the functional speed. The register bit assignments is given
in the next table.

Table 184.

BIST2_CFG_CTR register bit assignments

BIST2_CFG_CTR Register

0x0F8

Bit

Name

Reset
Value

Description

[31]

bist2_res_rst

1’h0

Reset status register result (BIST2_STS_RES)

1’b0: Disable reset

1’b1: Active reset

[30:29]

RFU

-

Reserved for future use (Write don’t care - Read return
zeros).

[28]

bist2_rst

1’h0

Reset BIST engine collar:

1’b0: Disable reset.

1’b1: Active reset

[27]

[26]

[25]

[24]

bist2_tm

bist2_debug

bist2_ret

bist2_iddq

1’h0

1’h0

1’h0

1’h0

Memory BIST interface command: command code and
BIST engine actions are detailed in the Memory BIST
Command Table

[23:04]

RFU

-

[03:00]

rbact2(03:00)

4’h0

Run BIST execution command (ref. Memory BIST
command):

1’b0: Disable BIST command.

1’b1: Run BIST command: memory BIST execution can be
done either in single or group mode (ref. next table)

Run BIST command table

Rbact

Memory Cut

Peripherals

[03]

ST_SPREG_2048
X32m8_Lb

RAS Local Data
Buffer-0

[02]

ST_DPHS_1024X
32m8_Lb

RAS Local Data
Buffer - 1

[01]

ST_DPHD_128X8
m4_L

RAS HWACC
Data Buffer

[00]

ST_DPHD_96X12
8m4_b (RAS)

RAS HWACC
Data Descriptor

«
...
248
249
250
251
252
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: C-TEC Pages: 2

Brand: FAAC Pages: 64

Brand: Jands Pages: 6

Brand: KEB Pages: 16

Brand: Wang Pages: 68

Brand: NAVITAS Pages: 14

Brand: Full Gauge Controls Pages: 3

Brand: Velleman Pages: 12

Brand: Nemesis Pages: 6

Brand: I-Tork Pages: 15

Brand: Click2Enter Pages: 34

Brand: LAUNDRY SOLUTION Pages: 14

Brand: Tescom Pages: 15

Brand: NDS Pages: 20

Brand: Aurora Scientific Pages: 21

Brand: Clare Controls Pages: 3

Brand: Swegon Pages: 11

Keyboard Controller Series

Brand: M-Audio Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands