STMicroelectronics SPEAr300 Reference Manual Download Page 244 | Manualshive

Page: 244 / 844

background image

Miscellaneous registers (Misc)

RM0082

Doc ID 018672 Rev 1

12.4.26 COMPSSTL_1V8_CFG/DDR_2V5_COMPENSATION register

The COMPSSTL_1V8_CFG/DDR_2V5_COMPENSATION is R/W registers which configure
the internal SSTL compensation cells parameters. The register bit assignments is given in
the next table.

12.4.27 COMPCOR_3V3_CFG

register

The COMPCOR_3V3_CFG is a R/W register which configures the internal CORE
compensation cell parameters. The register bit assignments is given in the next table.

Table 180.

COMPSSTL_1V8_CFG/DDR_2V5_COMPENSATION register bit
assignments

COMPSSTL_1V8_CFG Register

0x0E4

Bit

Name

Reset Value Description

[31]

TQ

1’h0

It enables IDDq mode.

[30:24]

rasrc

7'h78

Writing code compensation parameter: field sampled from
the compensation macro-cell during Read operating mode
command (ref. Compensation cell operating mode table).

[23]

RFU

-

Reserved for future use (Write don’t care - Read return zeros)

[22:16]

nasrc

-

Read code compensation parameter (RO); this field is
qualified from ‘sts_ok’ active high.

[15:05]

RFU

-

Reserved for future use (Write don’t care - Read return
zeros).

[04]

COMPOK

1’h0

Valid code compensation (RO); field actives high in normal
mode when the measured code is available on the
compensation bus nasrc.

[03]

accurate

1’h1

Compensation cell internal/external reference resistance
definition:

1’b0: Internal reference resistor

1’b1: External reference resistor: used to improve the
accuracy of compensation code value.

[02]

freeze

1’h0

Freeze command: when high freezes the current calculated
value of compensation bus.

[01]

comptq

1’h0

Compensation cell internal command parameter (ref.
Compensation cell operating mode table)

[00]

compen

1’h0

Compensation cell internal command parameter (ref.
Compensation cell operating mode table).

«
...
242
243
244
245
246
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

vlt soft starter mcd 500

Brand: Danfoss Pages: 95

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 33

Brand: Danfoss Pages: 59

Brand: Danfoss Pages: 16

VLT AQUA Drive FC 200

Brand: Danfoss Pages: 91

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 100

Brand: Danfoss Pages: 82

Brand: Danfoss Pages: 18

Brand: Danfoss Pages: 12

OPTYMA Plus OP-LPQM

Brand: Danfoss Pages: 8

Brand: Parker Pages: 12

Brand: Samson Pages: 8

Brand: RadioMaster Pages: 10

Brand: Vacon Pages: 132

Brand: National Instruments Pages: 34

Brand: Lab.gruppen Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands