STMicroelectronics SPEAr300 Reference Manual Download Page 154

Page: 154 / 844

DDR memory controller (MPMC)

RM0082

154/844

Doc ID 018672 Rev 1

MEM50_CTL

0xC8

0x32

AHB3_WRCNT

AHB3_RDCNT

MEM51_CTL

0xCC

0x33

AHB4_WRCNT

AHB4_RDCNT

MEM52_CTL

0xD0

0x34

This register intentionally blank.

MEM53_CTL

0xD4

0x35

This register intentionally blank.

MEM54_CTL

0xD8

0x36

TREF

MEM55_CTL

0xDC

0x37

EMRS3_DATA

MEM56_CTL

0xE0

0x38

TRAS_MAX

TDLL

MEM57_CTL

0xE4

0x39

TXSR

TXSNR

MEM58_CTL

0xE8

0x3A

VERSION

MEM59_CTL

0xEC

0x3B

TINIT

MEM60_CTL

0xF0

0x3C

OUT_OF_RANGE_ADDR[31:0]

MEM61_CTL

0xF4

0x3D

OUT_OF_RANGE_ADDR[33:32]

MEM62_CTL

0xF8

0x3E

This register intentionally blank.

MEM63_CTL

0xFC

0x3F

This register intentionally blank.

MEM64_CTL

0x100

0x40

This register intentionally blank.

MEM65_CTL

0x104

0x41

DLL_DQS_DELAY_BYPASS_0

MEM66_CTL

0x108

0x42

DLL_INCREMENT

DLL_DQS_DELAY_BYPASS_1

MEM67_CTL

0x10C

0x43

DLL_START_POINT

DLL_LOCK

MEM68_CTL

0x110

0x44

WR_DQS_SHIFT_BYPASS

DQS_OUT_SHIFT_BYPASS

MEM69_CTL

0x114

0x45

This register intentionally blank.

MEM70_CTL

0x118

0x46

This register intentionally blank.

MEM71_CTL

0x11C

0x47

This register intentionally blank.

MEM72_CTL

0x120

0x48

This register intentionally blank.

MEM73_CTL

0x124

0x49

This register intentionally blank.

MEM74_CTL

0x128

0x4A

This register intentionally blank.

MEM75_CTL

0x12C

0x4B

This register intentionally blank.

MEM76_CTL

0x130

0x4C

This register intentionally blank.

MEM77_CTL

0x134

0x4D

This register intentionally blank.

Table 77.

Registers overview (continued)

Register name

Offset

Mem. CTRL
core Reg.
Address

Type

(1)

Parameter(s)

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands

STMicroelectronics SPEAr300, Reference Manual

Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands