STMicroelectronics SPEAr300 Reference Manual Download Page 166

Page: 166 / 844

DDR memory controller (MPMC)

RM0082

166/844

Doc ID 018672 Rev 1

10.13.25 MEM20_CTL

register

10.13.26 MEM21_CTL

register

Table 98.

MEM20_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:28] -

Reserved. Read undefined. Write should be
zero.

[27:24]

AHB0_PRIORITY2_RE
LATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 2 CMDs from port
0.

[23:20] -

Reserved. Read undefined. Write should be
zero.

[19:16]

AHB0_PRIORITY1_RE
LATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 1 CMDs from port
0.

[15:12] -

Reserved. Read undefined. Write should be
zero.

[11:08]

AHB0_PRIORITY0_RE
LATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 0 CMDs from port
0.

[07:06] -

Reserved. Read undefined. Write should be
zero.

[05:00] AGE_COUNT

0x0

0x0 - 0x3F

Initial value of master generate counter for
CMD aging.

Table 99.

MEM21_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:28] -

Reserved. Read undefined. Write should be
zero.

[27:24]

AHB0_PRIORITY6_REL
ATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 6 CMDs from port
0.

[23:20] -

Reserved. Read undefined. Write should be
zero.

[19:16]

AHB0_PRIORITY5_REL
ATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 5 CMDs from port
0.

[15:12] -

Reserved. Read undefined. Write should be
zero.

[11:08]

AHB0_PRIORITY4_REL
ATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 4 CMDs from port
0.

[07:04] -

Reserved. Read undefined. Write should be
zero.

[03:00]

AHB0_PRIORITY3_REL
ATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 3 CMDs from port
0.

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands

STMicroelectronics SPEAr300, Reference Manual

Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands