STMicroelectronics SPEAr300 Reference Manual Download Page 342 | Manualshive

Page: 342 / 844

background image

BS_DMA controller

RM0082

Doc ID 018672 Rev 1

19.7.8 DMACRawIntTCStatus

register

The DMACRawIntTCStatus (raw interrupt terminal count status) is a RO register which
indicates the DMA channels that are requesting a transfer complete, terminal count
interrupt, prior to masking. The DMACRawIntTCStatus bit assignments are given in

19.7.9 DMACRawIntErrorStatus

register

The DMACRawIntErrorStatus (raw interrupt error status) is a RO register which indicates
the DMA channels that are requesting an errror interrupt prior to masking. The
DMACRawIntErrorStatus bit assignments are given in

.

19.7.10 DMACEnbldChns

register

The DMACEnbldChns (enabled channel) is a RO register which indicates the DMA
channels that are enabled, as indicated by the Enable bit (E) in the DMACCnConfiguration
register (

Section 19.7.15

). The DMACEnbldChns bit assignments are given in

Table 287.

DMACRawIntTCStatus register bit assignments

Bit

Name

Reset value Description

[31:08]

Reserved

-

Read: undefined.

[07:00]

RawIntTCStatus

8’h00

Status of the terminal count interrupt prior to masking.

Each bit is associated to a DMA channel. If a bit is set,
it means that a terminal count interrupt request is
active prior to masking for the relevant DMA channel.

Table 288.

DMACRawIntErrorStatus register bit assignments

Bit

Name

Reset value

Description

[31:08]

Reserved

-

Read: undefined.

[07:00]

RawIntErrorStatus 8’h00

Status of the error interrupt prior to masking.

Each bit is associated to a DMA channel. If a bit is
set, it means that an error interrupt request is active
prior to masking for the relevant DMA channel.

Table 289.

DMACEnbldChns register bit assignments

Bit

Name

Reset value

Description

[31:08]

Reserved

-

Read: undefined.

[07:00]

EnabledChannels

8’h00

Channel enable status.

Each bit is associated to a DMA channel. If a bit is
set, it means that corresponding DMA channel is
enabled. A bit is cleared on completion of the DMA
transfer.

«
...
340
341
342
343
344
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 20

Brand: ZKTeco Pages: 14

Brand: Unico Pages: 164

Brand: WAC Pages: 5

Brand: Quantum Pages: 20

Brand: Festo Pages: 109

Brand: Topworx Pages: 8

Brand: Dungs Pages: 56

Brand: Emec Pages: 8

Brand: Swagelok Pages: 16

Brand: Linear Technology Pages: 5

Brand: KELCO Pages: 4

Brand: OCL Pages: 2

fantech IPF05-1L

Brand: SystemAir Pages: 2

Brand: Doepke Pages: 2

Brand: KEPCO Pages: 34

Brand: THOR Pages: 12

CY3250-PLC20QFN

Brand: Cypress Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands