STMicroelectronics SPEAr300 Reference Manual Download Page 449 | Manualshive

Page: 449 / 844

background image

RM0082

HS_USB2.0 host

Doc ID 018672 Rev 1

22.6.33 HcPeriodCurrentED

register

The HcPeriodCurrentED register contains the physical address of the current Isochronous
or Interrupt Endpoint Descriptor.

Table 373.

HcPeriodCurrentED register bit assignments

22.6.34 HcControlHeadED

register

The HcControlHeadED register contains the physical address of the first Endpoint
Descriptor of the Control list.

Table 374.

HcControlHeadED register bit assignments

22.6.35 HcControlCurrentED

register

The HcControlCurrentED register contains the physical address of the current Endpoint
Descriptor of the Control list.

Table 372.

HcHCCA register bit assignments

Bits

Name

Reset

Read/Write

Description

HCD

HC

[31:08]

HCCA

0h

R/W

R

This is the base address of the Host Controller

Communication Area.

[07:00]

Reserved

Bits

Name

Reset

Read/Write

Description

HCD

HC

[31:04]

PCED

0h

R

R/W

PeriodCurrentED

This is used by HC to point to the head of one of the
Periodic lists which will be processed in the current
Frame. The content of this register is updated by HC after
a periodic ED has been processed. HCD may read the
content in determining which ED is currently being
processed at the time of reading.

[03:00]

Reserved

Bits

Name

Reset

Read/Write

Descritpion

HCD

HC

[31:04]

CHED

0h

R/W

R

ControlHeadED

HC traverses the Control list starting with the
HcControlHeadED pointer. The content is loaded from
HCCA during the initialization of HC.

[03:00]

Reserved

«
...
447
448
449
450
451
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: FrSky Pages: 2

Brand: Radware Pages: 98

Brand: Valcom Pages: 3

Brand: Valcom Pages: 2

Brand: Watts Pages: 17

Brand: Carel Pages: 36

Enclosure ENCR-10

Brand: suprema Pages: 18

Brand: maxon motor Pages: 44

Brand: Beckhoff Pages: 67

Brand: Omron Pages: 12

Brand: Invacare Pages: 44

RailBoss 4 Basic

Brand: G-Scale Graphics Pages: 22

Brand: Interactive Technologies Pages: 431

Brand: Hamamatsu Pages: 50

AK-CC 750 series

Brand: Danfoss Pages: 96

Brand: Samson Pages: 64

Brand: Woodward Pages: 24

Brand: WiTi Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands