STMicroelectronics SPEAr300 Reference Manual Download Page 164

Page: 164 / 844

DDR memory controller (MPMC)

RM0082

164/844

Doc ID 018672 Rev 1

10.13.20 MEM15_CTL

register

10.13.21 MEM16_CTL

register

‘

10.13.22 MEM17_CTL

register

[07:03] -

Reserved. Read undefined. Write should
be zero.

[02:00] AHB3_R_PRIORITY

0x0

0x0 - 0x7

Priority of read commands from port 3.

Table 92.

MEM14_CTL register bit assignments (continued)

Bit

Name

Reset
value

Range

Description

Table 93.

MEM15_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:03] -

Reserved. Read undefined. Write should be
zero.

[02:00] AHB4_W_PRIORITY 0x0

0x0 - 0x7

Priority of write commands from port 4.

Table 94.

MEM16_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:00] -

Reserved. Read undefined. Write should be
zero.

Table 95.

MEM17_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:27] -

Reserved. Read undefined. Write should be
zero.

[26:24] TCKE

0x0

0x0 - 0x7

Minimum CKE pulse width.

[23:19] -

Reserved. Read undefined. Write should be
zero.

[18:16]

OUT_OF_RANGE_S
OURCE_ID

0x0

0x0 - 0x7

Source ID of CMD that caused an Out-of-
Range interrupt. READ-ONLY

[15:11] -

Reserved. Read undefined. Write should be
zero.

[10:08] COLUMN_SIZE

0x0

0x0 - 0x7

Difference between number of column pins
available and number being used.

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands

STMicroelectronics SPEAr300, Reference Manual

Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands