STMicroelectronics SPEAr300 Reference Manual Download Page 696 | Manualshive

Page: 696 / 844

background image

RS_SDIO controller

RM0082

Doc ID 018672 Rev 1

-

0x03E

-

Reserved

CAP1

0x040

32

Capabilities registers

CAP2

0x044

32

Reserved

MAXCURR1

0x048

32

Maximum current capabilities register

MAXCURR2

0x04C

32

Reserved

ACMD12FEERSTS

0x050

16

Force event register for auto CMD12
error status

FEERRINTSTS

0x052

16

Force event register for error interrupt
status

ADMAERRSTS

0x054

8

ADMA error status register

-

0x055 to0x057

-

Reserved

ADMAAddr1

0x058

32

ADMA LSB system address register

ADMAAddr2

0x05C

32

ADMA MSB system address register

-

0x060 to 0x0EE

-

Reserved

SPIIRQSUPP

0x0F0

8

SPI Interrupt request support register

-

0x0F2 to 0x0FA

Reserved

SLTIRQSTS

0x0FC

16

Slot Interrupts register

HCTRLVER

0x0FE

16

Host controller version register

Table 616.

Register field types

Attribute

Description

RO

Read Only Register: Register bits are read only and cannot be altered by software or
any reset operation. Write to these bits are ignored.

ROC

Read Only Status: These bits are initialized to zero at reset. Writes to these bits are
ignored.

RW

Read-Write Register: Register bits are read-write and may be either set or cleared by
software to the desired state.

RW1C

Read Only Status, Write logic ‘1’ to clear Status: Register bits indicate status when
read, a set bit indicating a status event may be cleared by writing a logic ‘1’. Writing a
logic ‘0’ to RW1C bits has no effect.

RWAC

Read-Write, automatic clear register: The Host driver requests a Host Controller
operation by setting the bit. The Host Controller shall clear the bit automatically when
the operation of complete. Writing a logic ‘0’ to RWAC bits has no effect.

Hwinit

Hardware Initialized: Register bits are freezed. Bits are read only after initialization,
and writes to these bits are ignored.

Rsvd

Reserved: These bits are initialized to zero, and writes to them are ignored.

Table 615.

SDIO registers map (continued)

Name

Offset

Size in bit

Description

«
...
694
695
696
697
698
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: Accel Pages: 8

Brand: Danfoss Pages: 85

VLT Decentral FCD 300

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 4

VLT 6000 series

Brand: Danfoss Pages: 27

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

ADAP-KOOL AK-PC 781

Brand: Danfoss Pages: 14

Brand: Danfoss Pages: 12

vlt soft starter mcd 500

Brand: Danfoss Pages: 96

Brand: Casambi Pages: 2

Brand: HANYOUNG NUX Pages: 4

Brand: Eaton Pages: 2

Brand: Progres Pages: 2

Brand: YASKAWA Pages: 157

Brand: iceqube Pages: 2

Brand: Fego Precision Industrial Pages: 2

Smart-Flex FLX-4629

Brand: Cumberland Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands