STMicroelectronics SPEAr300 Reference Manual Download Page 181

Page: 181 / 844

RM0082

DDR memory controller (MPMC)

Doc ID 018672 Rev 1

181/844

10.13.68 MEM68_CTL

register

10.13.69 MEM[69-97]_CTL register

10.13.70 MEM[98-99]_CTL register

Note:

Only the USER_DEF_REG(0) bit 0 is used in SPEAr300. All the other bits are reserved.

[15:10] -

Reserved. Read undefined. Write should be zero.

[09:00] dll_lock

0x0

0x1 - 0x3FF

Number of delay elements in master DLL lock.

READ ONLY

Table 140.

MEM67_CTL register bit assignments (continued)

Bit

Name

Reset
value

Range

Description

Table 141.

MEM68_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:26] -

Reserved. Read undefined. Write should be
zero.

[25:16] wr_dqs_shft_byps

0x0

0x1 - 0x3FF

Number of delay elements to include in the
ddr_close signal in the controller when the DLL
is being bypassed.

[15:10] -

Reserved. Read undefined. Write should be
zero.

[09:00] dqs_out_shft_byps

0x0

0x1 - 0x3FF

Number of delay elements to include in the write
dqs signal to the DRAMs during WRITEs when
the DLL is being bypassed.

Table 142.

MEM[69-97]_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:00] -

Reserved. Read undefined. Write should be zero.

Table 143.

MEM[98-99]_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:00] user_def_reg(x) 0x0

0x0 - 0xFFFF_FFFF

User defined register.

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands

STMicroelectronics SPEAr300, Reference Manual

Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands