STMicroelectronics SPEAr300 Reference Manual Download Page 177

Page: 177 / 844

RM0082

DDR memory controller (MPMC)

Doc ID 018672 Rev 1

177/844

10.13.52 MEM49_CTL

register

10.13.53 MEM50_CTL

register

10.13.54 MEM51_CTL

register

Table 125.

MEM49_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:26] -

Reserved. Read undefined. Write should be
zero.

[25:16] AHB2_WRCNT 0x000

0x000 - 0x7FF

Number of bytes for an INCR WRITE CMD on
port 2.

[15:11] -

Reserved. Read undefined. Write should be
zero.

[10:00] AHB2_RDCNT

0x000

0x000 - 0x7FF

Number of bytes for an INCR READ CMD on
port 2.

Table 126.

MEM50_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:26] -

Reserved. Read undefined. Write should be
zero.

[25:16] AHB3_WRCNT

0x000

0x000 - 0x7FF

Number of bytes for an INCR WRITE CMD on
port 3.

[15:11] -

Reserved. Read undefined. Write should be
zero.

[10:00] AHB3_RDCNT

0x000

0x000 - 0x7FF

Number of bytes for an INCR READ CMD on
port 3.

Table 127.

MEM51_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:26] -

Reserved. Read undefined. Write should be
zero.

[25:16] AHB4_WRCNT

0x000

0x000 - 0x7FF

Number of bytes for an INCR WRITE CMD on
port 4.

[15:11] -

Reserved. Read undefined. Write should be
zero.

[10:00] AHB4_RDCNT

0x000

0x000 - 0x7FF

Number of bytes for an INCR READ CMD on
port 4.

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands

STMicroelectronics SPEAr300, Reference Manual

Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands