STMicroelectronics SPEAr300 Reference Manual Download Page 672

Page: 672 / 844

RS_Flexible static memory controller (FSMC)

RM0082

672/844

Doc ID 018672 Rev 1

31.4.10

GenMemCtrl peripheral identification registers (GenMemCtrlPeripID0-
3)

The GenMemCtrlPeriphID0-3 registers are four read only 8-bit registers. The bit
assignments are:-

Table 602.

GenMemCtrlPeriphID0 register bit assignments

Table 603.

GenMemCtrlPeriphID1 register bit assignments

Table 604.

GenMemCtrlPeriphID2 register bit assignments

Table 605.

GenMemCtrlPeriphID3 register bit assignments

31.4.11

GenMemCtrl cell Identification registers (GenMemCtrlPCellID0-3)

The GenMemCtrlPCellID0-3 registers are four read only 8-bit registers. The bit assignments
are -

Bit

Name

Reset
value

Description

[31:08]

Reserved. Read undefined. Write: should be zero.

[07:00]

PartNumber0

8'h90

These bits read back as 0x90

Bit

Name

Reset
value

Description

[31:08]

Reserved. Read undefined. Write: should be zero.

[07:04]

Designer0

4'h00

These bits read back as 0x0

[03:00]

PartNumber1

4‘h00

These bits read back as 0x0

Bit

Name

Reset
value

Description

[31:08]

Reserved. Read undefined. Write: should be zero.

[07:04]

Revision

4'h00

These bits return the peripheral revision.

[03:00]

Designer1

4‘h08

These bits read back as 0x8

Bit

Name

Reset
value

Description

[31:08]

Reserved. Read undefined. Write: should be zero.

[07:00]

Configuration

8'h00

These bits read back as 0x00

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands

STMicroelectronics SPEAr300, Reference Manual

Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands