manualshive.com logo in svg

STMicroelectronics SPEAr300, Reference Manual

The STMicroelectronics SPEAr300 is a high-performance, energy-efficient microprocessor that offers advanced processing capabilities. Users can enhance their understanding of the device by accessing the comprehensive Reference Manual available for free download on our website. Explore the manual and optimize the performance of your SPEAr300 today!

Share
Download
background image

RM0082

RS_SDIO controller

Doc ID 018672 Rev 1

717/844

         

[01]

TRNCPL

1’h0

RW1C

This bit is set when a read / write transaction is
completed. 

Read Transaction:

This bit is set at the falling edge of Read Transfer
Active Status. There are two cases in which the
Interrupt is generated. The first is when a data
transfer is completed as specified by data length
(After the last data has been read to the Host
System). The second is when data has stopped at
the block gap and completed the data transfer by
setting the Stop At Block Gap Request in the Block
Gap Control Register (After valid data has been
read to the Host System). 

Write Transaction:

This bit is set at the falling edge of the DAT Line
Active Status. There are two cases in which the
Interrupt is generated. The first is when the last
data is written to the card as specified by data
length and Busy signal is released. The second is
when data transfers are stopped at the block gap by
setting Stop At Block Gap Request in the Block Gap
Control Register and data transfers completed.
(After valid data is written to the SD card and the
busy signal is released).

Transfer Complete has higher priority than Data
Time-out Error. If both bits are set to logic ‘1’, the
data transfer can be considered complete.

1’b0 - No Data Transfer Complete

1’b1 - Data Transfer Complete

[00]

CMDCPL

1’h0

RW1C

This bit is set when get the end bit of the command
response (Except Auto CMD12).

Command Time-out Error has higher priority than
Command Complete. If both are set to logic ‘1’, it
can be considered that the response was not
received correctly.

1’b0 - No Command Complete

1’b1 - Command Complete

Table 637.

Relation between transfer complete and data time out error

Transfer complete

Command time out error

Meaning of the status

0

0

Interrupted by Another Factor.

0

1

Timeout occur during transfer.

1

Don’t care

Data Transfer Complete.

Table 636.

NIRQSTAT register bit assignments (continued)

Bit

Name

Reset 
value

Type

Description

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Vacon 20 Quick Manual preview
20
Brand: Vacon Pages: 62
S-COM 7K Manual preview
7K
Brand: S-COM Pages: 400
I-Tork PDS Series Installation & Operation Manual preview
PDS Series
Brand: I-Tork Pages: 15
Bailey infi 90 IMMFP12 Instruction preview
infi 90 IMMFP12
Brand: Bailey Pages: 75
GEM DG-2000 Series Operation Manual preview
DG-2000 Series
Brand: GEM Pages: 17
Xylem Bell & Gossett Technologic PPS Quick Start Manual preview
Bell & Gossett Technologic PPS
Brand: Xylem Pages: 20
Festo CPX-CEC Electronic Manual preview
CPX-CEC
Brand: Festo Pages: 87
ISVT IVC3100 Instruction Manual preview
IVC3100
Brand: ISVT Pages: 78
Linear Technology LT8610A Demo Manual preview
LT8610A
Brand: Linear Technology Pages: 8
4IPNET WHG301 Quick Installation Manual preview
WHG301
Brand: 4IPNET Pages: 11
Sturtevant Richmont Global 400mp User Manual preview
Global 400mp
Brand: Sturtevant Richmont Pages: 73
Oriental motor A Step AZ Series User Manual preview
A Step AZ Series
Brand: Oriental motor Pages: 120
National Instruments sbRIO-9698 User Manual preview
sbRIO-9698
Brand: National Instruments Pages: 12
D+H DXD 150-K-BSY+ Original Instructions Manual preview
DXD 150-K-BSY+
Brand: D+H Pages: 20
PTZOptics PT-JOY-G4 Quick Start Manual preview
PT-JOY-G4
Brand: PTZOptics Pages: 4
Kustom Signals Eyewitness HD ICV System Quick Reference Manual preview
Eyewitness HD ICV System
Brand: Kustom Signals Pages: 4
Teradek CTRL.1 Quick Start Manual preview
CTRL.1
Brand: Teradek Pages: 10
B&K Reference 20 Plus A/V System Controller Owner'S Manual preview
Reference 20 Plus A/V System Controller
Brand: B&K Pages: 84

Brands by name

Popular brands

Load more brands