STMicroelectronics SPEAr300 Reference Manual Download Page 247 | Manualshive

Page: 247 / 844

background image

RM0082

Miscellaneous registers (Misc)

Doc ID 018672 Rev 1

12.4.29

Memory BIST execution control

12.4.30 BIST1_CFG_CTR

register

The BIST1_CFG_CTR is an R/W register which configures and controls the internal core
memory BIST execution at the functional speed. The register bit assignments is given in the
next table.

[03]

S_W_mode

1’h1

SSTL pad drive strength mode: the overall drive
strength picture is detailed here below.

1’b0: Strong drive strength.

1’b1: Weak drive strength.

This bit changes the output impedance of the pad.

[02]

PROG_a

1’h0

Combination of these bits selects the speed of
operation of PAD, 00->200 MHz, 01->266 MHz, 10-
>333 MHz, 11->Prohibited.

[01]

PROG_b

1’h1

[00]

DDR_LOW_POWER_
DDR2_mode

1’h0

It selects DDR2(0) or DDR low power (1) mode.

Table 182.

DDR_PAD register bit assignments (continued)

DDR_PAD Register

0x0F0

Bit

Name

Reset
Value

Description

Table 183.

BIST1_CFG_CTR register bit assignments

BIST1_CFG_CTR Register

0x0F4

Bit

Name

Reset
Value

Description

[31]

bist1_res_rst

1’h0

Reset status register result (BIST1_STS_RES):

1’b0: Disable reset status.

1’b1: Active reset status.

[30:29}

RFU

-

Reserved for future use (Write don’t care - Read return zeros)

[28]

bist1_rst

1’h0

Reset BIST engine collar:

1’b0: Disable reset.

1’b1: Active reset.

«
...
245
246
247
248
249
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: Gardena Pages: 14

Brand: Gardena Pages: 4

GAT ACCESS 6100

Brand: Gantner Pages: 4

Brand: ICP DAS USA Pages: 166

Brand: ICP DAS USA Pages: 64

Tunnel Master Jr

Brand: ICS Pages: 83

Brand: fadini Pages: 28

Brand: HW Group Pages: 18

E4KP ENTRYCHECK

Brand: SDC Pages: 6

NuMicro M252 Series

Brand: Nuvoton Pages: 38

Brand: Cypress Pages: 571

Brand: Timotion Pages: 9

SmarTemp Control fx

Brand: Webasto Pages: 8

Brand: J+J Pages: 6

Brand: Sunlover Pages: 2

Brand: Grundfos Pages: 80

Brand: Casambi Pages: 4

Brand: Eaton Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands