STMicroelectronics SPEAr300 Reference Manual Download Page 486

Page: 486 / 844

HS_USB 2.0 device

RM0082

486/844

Doc ID 018672 Rev 1

23.8 Programming

model

23.8.1 External

pin

connection

23.8.2 Register

map

The 32 bit wide CSRs of the UDC-AHB subsystem (

Control and status registers on

page 468

) provide a high degree of control, making the device both configurable and

scalable. These CSRs can be accessed at the base address 0xE110_0000.

Table 394.

Plug status register bit assignments

Bit

Name

Reset value Description

[31:04]

Reserved

Read: undefined. Write: should be zero.

[03]

phy_mode

1’h1

USB PHY mode.

This bit allows to set the physical terminations of PHY,
according to encoding:

1‘b0 = Normal (UDC is allowed to drive the USB 2.0
PHY).

1‘b1 = Tri-state (the USB 2.0 PHY is in non-driving
mode).

[02]

phy_rst

1’h1

USB PHY reset.

If set, this bit indicates that the USB PHY is in reset
mode, otherwise it is in normal mode.

[01]

state

1’h0

USB host connection state.

This RO bit reports the connection status of the USB
Host, according to encoding:

1‘b0 = Disconnected.

1‘b1 = Connection detected.

[00]

enable

1’h0

Plug interrupt.

If set, this bit enables an interrupt to be raised when
the USB host is attached/detached.

Table 395.

Plug pending register bit assignments

Bit

Name

Reset value Description

[31:01]

Reserved

Read: undefined. Write: should be zero.

[00]

intpend

1’h0

Plug interrupt.

This bit is set when the UPD block generates a plug
interrupt. It is cleared when the CPU reads it.

Signal name

Pin

Description

DEV_DP

Device, positive data line

DEV_DM

Device, negative data line

DEV_VBUS

Device, VBUS detection line

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands

STMicroelectronics SPEAr300, Reference Manual

Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands