STMicroelectronics SPEAr300 Reference Manual Download Page 232

Page: 232 / 844

Miscellaneous registers (Misc)

RM0082

Doc ID 018672 Rev 1

12.4.14 AMEM_CFG_CTRL

register

The AMEM_CFG_CTRL is an R/W register which configures and controls the
asynchronous/synchronous memory port-1 source clock definition.

The output frequency originated from the x/y clock synthesizer is given from the next
equation:

with Y < 256; X < Y/2; Fin = (ref. amem_synt_enb source clock definition).

The register bit assignments is detailed in the next table.

Table 168.

PRSC1/2/3_CLK_CFG register bit assignments

PRSC1_CLK_CFG Register

PRSC2_CLK_CFG

PRSC3_CLK_CFG

0x044

0x048

0x04C

Bit

Name

Reset
Value

Description

[31:16]

RFU

Reserved for future use (Write don’t care - Read return
zeros).

[15:12]

presc_n

4’h0

N (3:0) constant factor division value: N < 16.

[11:00]

presc_m

12’h0

M (11:0) constant division value: M < 4096.

Table 169.

AMEM_CFG_CTRL register bit assignments

AMEM_CFG_CTRL Register

0x050

Bit

Name

Reset
Value

Description

[31:24]

amem_xdiv

8’h0

X(7:0) clock synthesizer constant division: X < Y/2.

[23:16]

amem_ydiv

8’h0

Y(7:0) clock synthesizer constant division: Y<256.

[15]

amem_rst

1’h0

Memory port-1 soft reset command:

1’b0: Disable soft reset.

1’b1: Active soft reset command.

[14:05]

RFU

Reserved for future use (Write don’t care - Read return
zeros).

[04]

amem_synt_enb

1’h0

Enable memory port-1 clock synthesizer:

1’b0: Disable memory clock synthesizer; memory clock is
provided in agree with the amem_clksel source clock
definitions.

1’b1: Enable memory clock synthesizer; memory clock is
provided from clock synthesizer logic (ref. amen Fout
equation)

out

Fin

X
Y

----

⎝

⎠

⎛

⎞

⁄

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands

STMicroelectronics SPEAr300, Reference Manual

Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands