STMicroelectronics SPEAr300 Reference Manual Download Page 169

Page: 169 / 844

RM0082

DDR memory controller (MPMC)

Doc ID 018672 Rev 1

169/844

10.13.31 MEM26_CTL

register

10.13.32 MEM27_CTL

register

Table 104.

MEM26_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:28] -

Reserved. Read undefined. Write should be
zero.

[27:24]

AHB3_PRIORITY2_RE
LATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 2 CMDs from port
3.

[23:20] -

Reserved. Read undefined. Write should be
zero.

[19:16]

AHB3_PRIORITY1_RE
LATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 1 CMDs from port
3.

[15:12] -

Reserved. Read undefined. Write should be
zero.

[11:08]

AHB3_PRIORITY0_RE
LATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 0 CMDs from port
3.

[07:04] -

Reserved. Read undefined. Write should be
zero.

[03:00]

AHB2_PRIORITY7_RE
LATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 7 CMDs from port
2.

Table 105.

MEM27_CTL register bit assignments

Bit

Name

Reset
value

Range

Description

[31:28] -

Reserved. Read undefined. Write should be
zero.

[27:24]

AHB3_PRIORITY6_RE
LATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 6 CMDs from port
3.

[23:20] -

Reserved. Read undefined. Write should be
zero.

[19:16]

AHB3_PRIORITY6_RE
LATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 5 CMDs from port
3.

[15:12] -

Reserved. Read undefined. Write should be
zero.

[11:08]

AHB3_PRIORITY6_RE
LATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 4 CMDs from port
3.

[07:04] -

Reserved. Read undefined. Write should be
zero.

[03:00]

AHB3_PRIORITY3_RE
LATIVE_PRIORITY

0x0

0x0 - 0xF

Relative priority of priority 3 CMDs from port
3.

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands

STMicroelectronics SPEAr300, Reference Manual

Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands