STMicroelectronics SPEAr300 Reference Manual Download Page 210

Page: 210 / 844

Miscellaneous registers (Misc)

RM0082

210/844

Doc ID 018672 Rev 1

12.4 Miscellaneous

register local space

12.4.1 Overview

The local register space controls the following functionalities:-

●

SoC main configuration

–

Functional mode (up to 7 configuration are allowed):

–

Normal operating mode.

–

Debug mode: enable and control the processors embedded trace module and
Embedded ICE diagnostic functionalities.

–

Test manufacture mode.

●

Clock definition and control:

–

Source clock definition.

–

Setting operating frequency.

–

Clock gating control.

–

Auxiliary clock configuration.

●

Soft reset control.

●

Platform basic configuration parameters:

–

Switch matrix arbitration protocol and priority definition.

–

DMA channel assignment scheme.

–

USB2 Pays setting parameter.

●

Special configuration parameters:

–

Compensation pad parameters.

–

Fast IO pad configuration parameters.

–

SSTL pad basic functionality

–

Wake up configuration type.

●

Functional memory BIST execution control.

●

Diagnostic error detection.

12.4.2 Miscellaneous

register local space address map

Next table shows the miscellaneous register map.

Table 157.

Miscellaneous local space registers overview

Misc. Local Space Register Map

Base Address: 0xFCA8.0000

Register Name

Region-1 Offset

0x0.0000

Region-2 Offset

0x1.0000

Type

SOC_CFG_CTR

0x000

DIAG_CFG_CTR

0x004

R/W

PLL1_CTR

0x008

R/W

PLL1_FRQ

0x00C

R/W

PLL1_MOD

0x010

R/W

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands

STMicroelectronics SPEAr300, Reference Manual

Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands