manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 2   CPU

Rev. 2.00  Mar 09, 2006  page 33 of 906

REJ09B0292-0200

The name Ix is an alias for R8. The other aliases are assigned as follows:

Ax0:

.REG (R4)

Ax1:

.REG (R5)

Ix:

.REG (R8)

Ay0:

.REG (R6)

Ay1:

.REG (R7)

Iy:

.REG (R9)

As0:

.REG (R4)

defined when an alias is required for single data transfer

As1:

.REG (R5)

defined when an alias is required for single data transfer

As2:

.REG (R2)

defined when an alias is required for single data transfer

As3:

.REG (R3)

defined when an alias is required for single data transfer

Is:

.REG (R8)

defined when an alias is required for single data transfer

2.1.2

Control Registers

The six 32-bit control registers consist of the status register (SR), repeat start register (RS), repeat
end register (RE), global base register (GBR), vector base register (VBR), and modulo register
(MOD).

The SR register indicates processing states.

The GBR register functions as a base address for the indirect GBR addressing mode, and is used
for such as on-chip peripheral module register data transfers.

The VBR register functions as the base address of the exception processing vector area (including
interrupts).

The RS and RE registers are used for program repeat (loop) control. The repeat count is
designated in the SR register repeat counter (RC), the repeat start address in the RS register, and
the repeat end address in the RE register. However, note that the address values stored in the RS
and RE registers are not necessarily always the same as the physical start and end address values
of the repeat.

The MOD register is used for modulo addressing to buffer the repeat data. The modulo addressing
designation is made by DMX or DMY, the modulo end address (ME) is designated in the upper 16
bits of the MOD register, and the modulo start address (MS) is designated in the lower 16 bits.
Note that the DMX and DMY bits cannot simultaneously designate modulo addressing. Modulo
addressing is possible with X and Y data transfer instructions (MOVX, MOVY). It is not possible
with single data transfer instructions (MOVS).

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

NEC N8104-213 Installation Manual preview
N8104-213
Brand: NEC Pages: 10
NEC N8104-213 Instructions Manual preview
N8104-213
Brand: NEC Pages: 8
Panasonic MICROCOMPUTER MN103S Connection Diagrams preview
MICROCOMPUTER MN103S
Brand: Panasonic Pages: 5
Panasonic MICROCOMPUTER MN103S Application Note preview
MICROCOMPUTER MN103S
Brand: Panasonic Pages: 21
Panasonic FP2 Series Manual preview
FP2 Series
Brand: Panasonic Pages: 56
Panasonic FP2 Series Product Manual preview
FP2 Series
Brand: Panasonic Pages: 28
Panasonic KX-HTS Series Quick Start Manual preview
KX-HTS Series
Brand: Panasonic Pages: 2
Panasonic WJMPU955 - PROCESSING UNIT - TMU Operating Instructions Manual preview
WJMPU955 - PROCESSING UNIT - TMU
Brand: Panasonic Pages: 62
Paradyne Hotwire 5100 User Manual preview
Hotwire 5100
Brand: Paradyne Pages: 45
XNET INS2000 Install Manual preview
INS2000
Brand: XNET Pages: 17
H3C NSQ1GT48EA0 Manual preview
NSQ1GT48EA0
Brand: H3C Pages: 3
FDI ELI70-CR Quick Start Manual preview
ELI70-CR
Brand: FDI Pages: 2
ZALMAN CNPS7000A Series User Manual preview
CNPS7000A Series
Brand: ZALMAN Pages: 9
Moxa Technologies PT-7324 Series User Manual preview
PT-7324 Series
Brand: Moxa Technologies Pages: 36
ebm-papst W3G710-NK67-01 Operating Instructions Manual preview
W3G710-NK67-01
Brand: ebm-papst Pages: 13
Nortel BayStack 660 Use Manual preview
BayStack 660
Brand: Nortel Pages: 163
Baracoda Scan Dongle User Manual preview
Scan Dongle
Brand: Baracoda Pages: 16
FiberHome AN5506-04-F User Manual preview
AN5506-04-F
Brand: FiberHome Pages: 2

Brands by name

Popular brands

Load more brands